FAAC E 578D Manual
  1. Manuals
  2. Brands
  3. FAAC Manuals
  4. Computer Hardware
  5. E 578D
  6. Manual
FAAC E 578D Manual

FAAC E 578D Manual

Control board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
E 578D

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E 578D and is the answer not in the manual?

Questions and answers

Related Manuals for FAAC E 578D

Summary of Contents for FAAC E 578D

  • Page 1 E 578D...

  • Page 2: Table Of Contents

    INDEX CE DECLARATION OF CONFORMITY .......................... 2 WARNINGS FOR THE INSTALLER ..........................2 1 WARNINGS ................................3 2 TECHNICAL SPECIFICATIONS ..........................3 3 LAYOUT AND COMPONENTS ..........................3 4 ELECTRIC CONNECTIONS ............................3 ..................4 CONNECTION OF PHOTOCELLS AND SAFETY DEVICES 4.2 TERMINAL BOARD - POWER SUPPLY (FIG.

  • Page 3: Ce Declaration Of Conformity

    12604 and EN 12605. prevent the automated system from being activated involuntarily. For non-EU countries, to obtain an adequate level of safety, the Standards mentioned above must be observed, in addition to national 23) Transit is permitted only when the automated system is idle. legal regulations. 24) The user must not attempt any kind of repair or direct action whatever 9) FAAC is not responsible for failure to observe Good Technique in and contact qualified personnel only. the construction of the closing elements to be motorised, or for any 25) Maintenance: check at least every 6 months the efficiency of the system, deformation that may occur during use. particularly the efficiency of the safety devices (including, where foreseen, 10) The installation must conform to Standards EN 12453 and EN 12445. the operator thrust force) and of the release devices.

  • Page 4: Warnings

    CONTROL BOARD 578D 1 WARNINGS 3 LAYOUT AND COMPONENTS Important: Before attempting any work on the control board (connections, maintenance), always turn off power. - Install, upstream of the system, a differential thermal breaker with adequate tripping threshold. - Connect the earth cable to the appropriate terminal on the J7 connector of the equipment (see fig.).

  • Page 5: Connection Of Photocells And Safety Devices

    NOTE: The 578D equipment is able to command electro-mechanical Connection of no safety device operators for sliding gates and industrial sectional doors. Anything referring to gates in these instructions also applies to doors. Any differences are shown in the specific paragraphs. 4.1 Connection of photocells and safety devices Before connecting the safety devices and photocells we advise Fig.
  • Page 6 Connection of a pair of opening photocells, a pair of closing Connection of a pair of closing photocells, a pair of opening photocell and an edge safety device photocells and a pair of opening/closing photocells Fig. 0 Connection of two pairs of closing photocells and two edge safety devices Fig.

  • Page 7: Terminal Board - Power Supply (Fig. 2)

    STOP - STOP contact (terminal 5): any device (e.g. a 4.2 Terminal board - Power supply (fig. 2) push-button) which, by opening a contact, stops gate POWER SUPPLY (terminals PE-N-L): movement. PE : Earth connection To install several STOP devices, connect the N.C. N : Power supply ( Neutral ) contacts in series (fig. 4).

  • Page 8: Connector J2 - Rapid Connection To Minidec, Decoder And Rp

    W.L. - Power supply to indicator light / timed exit / electric lock/ 'traffic lights' (terminal 6) Connect any 24 Vdc - 3 W max indicator light, timed exit, command device for electric lock or 'traffic lights' between MINIDEC PLUS this terminal and the +24V (see advanced programming in Chap.
  • Page 9 Fig. 9 Fig. 0 Fig. ...

  • Page 10: Programming

    5 PROGRAMMING 5.2 ADVANCED PROGRAMMING To program operation of the automated system, you have To access ADVANCED PROGRAMMING, press key F and, as to access the "PROGRAMMING" mode. you hold it down, press key Programming is split into two parts: BASIC and ADVANCED. •if you release key + , the display indicates the name of the first function. 5.1 BASIC PROGRAMMING •if you release key F too, the display shows the value of the To access BASIC PROGRAMMING, press key F: function that can be modified with keys + and -. •if you press it (and hold it down), the display shows the name •if you press key F (and hold it down), the display shows the of the first function. name of the next function, and if you release it, the value that •if you release the key, the display shows the value of the can be modified with keys + and - is shown. function that can be modified with keys + and -. •when you reach the last function, press F to exit the program, •if you press F again (and hold it down), the display shows the and the display resumes showing the gate status. name of the next function, etc. •when you reach the last function, press F to exit the program, The following table shows the sequence of functions and the display resumes showing the gate status.
  • Page 11 Display Function Default Display Function Default INDICATOR-LIGHT: ENCODER: is selected, the output functions as a If the encoder is used, you may select its presence. standard indicator-light (lighted at opening If the encoder is present and enabled, and pause, flashing at closing, and off when "decelerations"...

  • Page 12: Start-Up

    6 START-UP Display Function Default 6.1 Inputs check WORK TIME (time-out): We advise you to set a value of 5 to 10 seconds The table below shows the status of the LEDs in relation to to the over the time taken by the gate to travel from status of the inputs.

  • Page 13: Installation Using The 541 Operator

    NOTE - For motors with an inductive sensor (746 and 844) take 7 FINAL OPERATIONS care over setting post-limitswitch deceleration and braking: At end of programming, run a few complete cycles to check if if deceleration is too long or braking is insufficient, the plate the automated system and the accessories connected to it are fitted on the gate rack can go beyond the sensor until it operating correctly, giving special attention to safety devices, disengages the sensor. When the gate is stopped, check if operator thrust force adjustment, and to the anti-crushing only the limit-switch involved is engaged. The relevant LED device (Encoder sensor). Hand over the "User's guide" page (in must be off. If it went off and then re-lighted, or if both the the operator instructions) to the customer, and describe how...
  • Page 16 Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. FAAC se réserve le droit d’apporter à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à...

Table of Contents