Advertisement
Box Contents
STRIKE AMP 12 MK2
Power Cable
Quickstart Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit alesis.com.
For additional product support, visit alesis.com/support.
Items not listed under Introduction > Box Contents are sold separately.
Example A: One STRIKE AMP 12 MK2 (Mono)
Connect the Left (Mono) output of your drum module to the input on a STRIKE AMP 12 MK2.
Example B: Two STRIKE AMP 12 MK2s (Stereo)
Connect the Right and Left (Mono) outputs of your drum module to the inputs of your STRIKE AMP 12 MK2.
Example C: Two STRIKE AMP 12 MK2s (Mono)
Connect the Left (Mono) output of your drum module to the input of one STRIKE AMP 12 MK2, and then connect the Mix Out of that STRIKE AMP 12 MK2 to the input of another.
Pairing a Bluetooth Device
Try lowering the volume control of your sound source, musical instrument, or microphone.
I hear a hum when cables are connected:
Try adjusting the tone or EQ control on your sound source to lower the bass level. This will allow you to play the music louder before clipping (distortion) occurs.
If there is a high-pitched whistling noise when using microphones: This is probably feedback. Point the microphone away from the speaker.
If you can't hear the microphone over the music volume: Turn down the music volume from your source.
If you cannot connect your audio device to STRIKE AMP 12 MK2 via Bluetooth:
Output Power | 2500 W |
Drivers | Low-Frequency: 12.0" (305 mm) driver, 2.5" (63 mm) high-temperature voice coil. High-Frequency: 1.0" (25 mm) exit ceramic driver with 1.4" (35 mm) coil. |
Crossover Frequency | 2 kHz |
Maximum SPL | 132 dB (peak) dB-SPL @ 1 m |
Frequency Response | 53 Hz – 20 kHz (+/-3 dB) |
Frequency Range | 44 Hz – 20 kHz (-10 dB) |
Horn Coverage | 90° horizontal x 60° vertical (nominal) |
Connectors | (2) XLR+1/4" (6.35 mm) TRS combo inputs (Balanced) (1) XLR output (Link) (1) IEC power cable input |
Input Impedance | Line: 10 KΩ balanced, 20 KΩ unbalanced |
Gain/Volume Control Range | -∞ to 0 dB, +4 dBu nominal, +10 dBu for max output |
HPF Switch | 100 Hz |
Bluetooth | Version: 5.0 Profile: A2DP, AVRCP Codec: SBC Range: up to 100 feet (30.5m) |
Power | Connection: IEC Input Voltage: 100-120V, 50/60 Hz; 220-240V, 50/60 Hz Consumption: 1100W Fuse: T15AL AC250V; 220-240V T6.3AL AC250V |
Protection | Electronic clip, thermal, and transducer overdrive protection |
Mounting/Installation | Standard 36 mm pole socket |
Operating Temperature | 14°F to 113°F (-10°C to 45°C) |
Dimensions (width x depth x height) | 13.9" x 13.8" x 23.9" 351 mm x 354 mm x 607 mm |
Weight | 34.7 lbs. 15.7 kg |
Specifications are subject to change without notice.
Please note: Alesis and inMusic are not responsible for the use of its products or the misuse of this information for any purpose. Alesis and inMusic are not responsible for the misuse of its products caused by avoiding compliance with inspection and maintenance procedures. Please refer to the included safety and warranty manual for more information.
To reduce the risk of electric shock, do not connect a STRIKE AMP 12 MK2 loudspeaker to a power outlet while the grille is removed.
Mounting of any heavy load can result in serious injury and equipment damage. This work should be done by qualified persons following safe mounting practices in accordance with all applicable safety and construction standards. Such persons must determine the required load ratings and design factors. They must determine the mounting method that meets static, dynamic, shock, and any other load requirements. All such work must be done in accordance with and in compliance with all federal, state, and local regulations governing such work.
Preparation
Before placing, installing, or mounting any speaker product, inspect all hardware, cabinets, brackets, and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation or placement. The above conditions and others like it severely reduce the safety of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term, unexpected overloading. Ensure that all local, state, and national regulations regarding the safety and operation of loudspeakers and related equipment are understood and followed, paying special attention to applicable electrical and building codes.
Stand-Mounting
Sound Level
Permanent hearing loss may be caused by exposure to extremely high noise levels. The U.S. Occupational Safety and Health Administration (OSHA) has specified permissible exposures to certain noise levels. According to OSHA, exposure to high sound pressure levels (SPL) in excess of these limits may result in hearing loss. When using equipment capable of generating high SPL, use hearing protection while such equipment is under operation.
Hours per day | SPL (dB) | Example |
8 | 90 | Small gig |
6 | 92 | Train |
4 | 95 | Subway train |
3 | 97 | High-level desktop monitors |
2 | 100 | Classical music concert |
1.5 | 102 | Riveting machine |
1 | 105 | Machine factory |
0.5 | 110 | Airport |
0.25 or less | 115 | Rock concert |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the Strike Amp 12 and is the answer not in the manual?
Questions and answers