Hubbell CX16 Installation Instructions Manual

PRECAUTIONS
• READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• CAUTION: USE COPPER CONDUCTOR ONLY
• CAUTION: RISK OF ELECTRICAL SHOCK. To prevent electrical shock, turn off power at the circuit breaker before installing or servicing unit. Never wire
energized electrical components
• NOTE: For installation by licensed electrician in accordance with the National and/or Electrical Codes and the following instructions
• NOTE: Do not install if the product appears to be damaged. Be sure to read and understand all instructions before installing or servicing unit
• Run low voltage wiring with line voltage wiring in their respective compartments
• For indoor use only. Do not use outdoors unless all environmental requirements are met
• Do not mount near gas or electric heater
• Disconnect switch or a circuit breaker must be provided and marked as the disconnecting device
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition
• Confirm that device ratings are suitable for the application prior to installation
• No user serviceable parts contained inside unit. Refer all service related questions to the factory
• All servicing shall be performed by qualified service personnel
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel
• Use only approved materials and components (i.e. twist on connectors, electrical box, etc.) as appropriate for installation
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired
• Do not use this equipment for other than intended use
• If any Emergency Circuits are fed or controlled from this panel, it must be located electrically where fed from a UPS, generator, or other guaranteed
source of power during emergency and power outage situations
• The CX panel enclosure and door are a complete assembly. Doors are not purchased separately
• SAVE THESE INSTRUCTIONS!
DESCRIPTION
The CX Lighting Control Panels are lighting control systems designed to control lighting loads as well as motor loads up to 2 HP. The system includes an
enclosure, power supply and or transformer, motherboard with Class 2 I/O user interface, and relay cards to control loads. The relay card is an open-type
accessory intended for installation inside the panel.
PRODUCT CONFIGURATION
MODEL SPACES INPUT VOLTAGE
CX 16 16 relay spaces 2
24 3
24 relay spaces
Examples: CX162S162NM - CX 16 Relay Panel, 120-277VAC universal input, with 16 20A/1P N/O Electrically Held Relays installed in NEMA 1 Surface Mount
Master Panel.
RELAY MODEL RELAY TYPE
CXR 2N
3L
3LEM*
TN
TC*
Copyright © 2019 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identifiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
ENCLOSURE
120-277VAC S NEMA 1 Enclosure
347-480VAC
1-Pole, Electrically Held, N.O.,120/277VAC
1-Pole, Latching,120/277/347VAC
1-Pole, Latching,120/277/347VAC
2-Pole, Electrically Held, N.O., 208/240/480VAC
2-Pole, Electrically Held, N.C., 208/240/480VAC
701 Millennium Blvd. | Greenville, SC 29607 | (864) 678-1000 | (866) 898-0131 - fax www.hubbellcontrolsolutions.com
affiliation with or endorsement by such respective owners.
Lighting Control Panel 16 and 24
RELAY QUANTITY RELAY TYPE
00 No relays included SP Space Only
(Required SP Relay Type)
16 2N
16 relays installed 1-Pole elect. held N.O.
(fully populated) relays (CXR2N)
24 24 relays installed 3N 1-Pole latching relays
(fully populated) (CXR3L)
TN 2-Pole elect. held N.O.
relays (CXRTN)
INSTALLATION INSTRUCTIONS
OPTIONS
M Master (available in
CX16 or CX24)
S
Secondary (available in
CX16 or CX24)
72-00474C
3301B 043019