Page 1
Over the Range Installation Microwave Oven Instructions AVM4160, JNM3161, JVM3160, and RVM5160 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN Note to Consumer – Read these instructions completely and carefully. • Keep these instructions for future reference.
Installation Instructions Outside Back Exhaust ......21-24 CONTENTS Installation Overview ......21 General information Preparing Rear Wall for Important Safety Instructions ......3 Outside Back Exhaust ......21 Electrical Requirements ........3 Attach Mounting Plate to Wall ..21, 22 Tools You Will Need ..........4 Preparation of Top Cabinet ....
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS A qualified electrician must perform a ground Where a standard two-prong wall receptacle is encountered, it must be replaced with a properly continuity check on the wall receptacle before grounded three-prong wall receptacle, installed beginning the installation to ensure that the by a qualified electrician.
Installation Instructions TOOLS YOU WILL NEED #1 and #2 Pencil Carpenter square Phillips (optional) screwdriver Ruler or tape measure and straight edge Scissors (to cut template, if necessary) Tin snips (for cutting damper, if required) Filler blocks or scrap wood pieces, if needed Electric drill with 3 16 7 16...
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page Below are examples of Outside Top Exhaust and Outside Back Exhaust duct system layouts.
Page 6
Installation Instructions Maximum duct length: NOTE: If you need to install ducts, note that the total duct length of 3 For satisfactory air movement, the total duct length of round duct should not exceed 140 equivalent feet. x 10 rectangular or 6 diameter round duct should Outside ventilation requires a HOOD EXHAUST DUCT.
Installation Instructions PARTS INCLUDED DAMAGE – SHIPMENT/ INSTALLATION ADDITIONAL PARTS PART QUANTITY • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. Top Cabinet • If the unit is damaged by the customer, repair or Template replacement is the responsibility of the customer.
Installation Instructions MOUNTING SPACE NOTES: • The space between the cabinets must be 30 wide and free of obstructions. • This microwave oven is for installation over ranges up to 36 wide. max* Bottom edge of • If you are going to vent your microwave oven cabinet needs to the outside, see Hood Exhaust Section for to be 30 or...
Installation Instructions PLACEMENT OF THE MOUNTING PLATE FINDING THE WALL STUDS REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE Open the box and fold back all four carton flaps fully against the carton sides. Remove the following items from the protective foam: installation Wall instructions, filters, exhaust adaptor, damper, and...
Installation Instructions DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET Plate Position – recessed cabinet bottom Plate Position – flat bottom cabinet Mounting Plate Tabs Touching the Mounting Plate Tabs Back Frame of the Touching the Cabinet Cabinet Bottom 30 to Cooktop Plate Position –...
Installation Instructions ALIGNING THE MOUNTING PLATE 30” Hole B Draw a Hole A Vertical Line on Wall from Center of Top Cabinet Hole D Hole C Area E Notch CAUTION Wear gloves to avoid cutting NOTE: Holes C and D are inside area E. If neither fingers on sharp edges.
Installation Instructions INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the NOTE: Select the type of ventilation required for your following 3 types of ventilation: installation and proceed to that section. A. Recirculating (Non-Vented Ductless) B.
Installation Instructions RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Charcoal Filter (Supplied with AVM4160 and JVM3160 models) A4. Mount the microwave oven Conven ience Cooking Potato Beverage Popcorn Cook Defrost Time Reheat Weight/Tim...
Page 14
Installation Instructions ADJUST BLOWER MOTOR ADJUST BLOWER MOTOR (cont.) Fan Blades Remove the screws holding the blower unit and the screws securing the blower plate. Remove the blower plate from the outer case by sliding it toward the back of the microwave and pulling up. Blower Motor Screws Wires Back of...
Installation Instructions INSTALLING THE A5 MOUNT THE MICROWAVE OVEN CHARCOAL FILTER Remove 2 screws on top of microwave oven, just above the grille panel, using a Phillips screwdriver. If two screws are not accessible, see section A5. Open the door. Remove the grille.
Installation Instructions MOUNT THE MICROWAVE OVEN INSTALLING/REPLACING THE CHARCOAL FILTER WITHOUT (cont.) ACCESS TO TOP SCREWS AND Insert 3 self-aligning screws ( -28 x 2 ”) THE UNIT HAS ALREADY BEEN through outer top cabinet holes. Turn two full turns MOUNTED on each screw.
B1. Attach Mounting Plate to Wall B2. Prepare Top Cabinet B3. Adjust Blower Motor B4. Install Exhaust Adaptor B5. Mount Microwave Oven B6. Connect Ductwork Cooki ng Conve nienc e Potato Bevera ge Popco rn Cook Defros t Time Rehea t Weight/T ime Timer On/Off Expre ss Cook 30 Sec.
Installation Instructions ADJUST BLOWER MOTOR (cont. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP Rotate 90° CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. Back of Microwave Roll the blower so that fan blade openings are...
Installation Instructions MOUNT THE MICROWAVE OVEN ASSEMBLE AND INSTALL ADAPTOR Blower Plate Damper CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave) or property damage, you will need two people to install this microwave.
Installation Instructions MOUNT THE MICROWAVE OVEN CONNECTING DUCTWORK (cont.) Insert a self-aligning screw through top-center House Duct cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Insert 2 self-aligning screws ( -28 x...
C1. Prepare Rear Wall C2. Attach Mounting Plate to Wall C3. Prepare Top Cabinet C4. Adjust Blower C5. Mount the Microwave Oven Cooki ng Conve nienc e Potato Bevera ge Popco rn Defros t Cook Rehea t Time Weight/T ime Timer...
Installation Instructions ATTACH THE MOUNTING ADAPTING BLOWER FOR PLATE TO THE WALL (cont.) OUTSIDE BACK EXHAUST To use toggle bolts: 1 Remove the blower motor screws that holds the blower plate to the microwave oven. Slide the plate Spacing for Toggles More toward the back of the microwave and lift up to Than Wall Thickness remove.
Installation Instructions ADAPTING BLOWER FOR MOUNT THE MICROWAVE OVEN OUTSIDE BACK EXHAUST (cont. Gently place the fan back into the cavity with the exhaust portion of the fan at the top and facing the back of the unit. CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave) or property damage, you will need two people to install this microwave.
Page 24
Installation Instructions MOUNT THE MICROWAVE OVEN (cont.) Insert a self-aligning screw through top-center cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Insert 2 self-aligning screws ( -28 x ) through outer top cabinet...
Installation Instructions BEFORE YOU USE YOUR MICROWAVE OVEN Make sure the microwave oven has been Read the Owner’s Manual. installed according to instructions. Remove all packing material from the KEEP INSTALLATION INSTRUCTIONS microwave oven. FOR THE LOCAL INSPECTOR’S USE. Install turntable and turntable ring in cavity. Replace house fuse or turn breaker back on.
Page 26
Installation Instructions Printed in China...
Page 27
Horno microondas para Instrucciones colocar encima de la estufa de Instalación AVM4160, JNM3161, JVM3160 y RVM5160 ¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio web en: GEAppliances.com ANTES DE COMENZAR Nota para el Comprador – • Conserve estas Lea estas instrucciones en su totalidad y instrucciones para referencia futura.
Page 28
Instrucciones de Instalación Escape de Salida Trasero ....21-24 CONTENIDOS Visión General de la Instalación ..21 Información General Preparación de la Pared Trasera Instrucciones Importantes de Seguridad .... 3 para el Escape de Salida Trasero ..21 Requisitos Eléctricos ........... 3 Adjunte la Placa de Montaje a la Pared 21, 22 Herramientas Que Necesitará...
Instrucciones de Instalación INSTRUCCIONES IMPORTANTES DE SEGURIDAD Un electricista calificado deberá realizar un control de Cuando se encuentre un tomacorriente de pared la continuidad de la conexión a tierra en el receptáculo de dos enchufes, se deberá reemplazar por uno de la pared antes de comenzar con la instalación, conectado a tierra de forma adecuada de tres cables, a fin de asegurar que la caja del tomacorriente...
Page 30
Instrucciones de Instalación HERRAMIENTAS NECESARIA Destornillador Lápiz Escuadra de Phillips nº1 y nº2 carpintero (opcional) Regla o cinta métrica y extremo recto Tijeras (para cortar plantillas, si es necesario) Tijeras para hojalata (para cortes en reguladores, si se Bloques de llenado o piezas de requiere) fragmentos de madera, si son necesarios para para generar...
Instrucciones de Instalación CAMPANA DE ESCAPE NOTA: Lea las dos siguientes páginas sólo si planea ventilar su escape desde la parte exterior. Si planea hacer que el aire vuelva a circular en la habitación, pase a la página 6. A continuación figuran ejemplos de diagramas del sistema del conducto del Escape de Salida Superior y del Escape de Salida Trasero.
Page 32
Instrucciones de Instalación Longitud máxima de la tubería: NOTA: Si necesita instalar tuberías, deberá observar que la longitud total de una tubería rectangular de 3 1/4” x 10” o una Para un movimiento satisfactorio del aire, la longitud circular de 6” de diámetro no deberá superar los 140 pies de total de la tubería rectangular de 3 ¼”...
Instrucciones de Instalación DAÑO – ENVÍO/ PARTES INCLUIDAS INSTALACIÓN PIEZAS ADICIONALES • Si la unidad se daña durante el envío, devuelva PARTE CANTIDAD la unidad a la tienda donde fue comprada para su reparación o reemplazo. Plantilla del • Si la unidad es dañada por el cliente, la Gabinete reparación o reemplazo es responsabilidad del Superior...
Instrucciones de Instalación ESPACIO DE MONTAJE NOTAS: • El espacio entre los gabinetes debe ser de 30” de ancho y estar libre de obstrucciones. El extremo inferior del gabinete debe • Este horno microondas debe ser instalado sobre Máx. de estar a 30”...
Instrucciones de Instalación COLOCACIÓN DEL PLATO DE MONTAJE RETIRO DEL HORNO BÚSQUEDA DEL MICROONDAS DE LA CAJA/ MONTAJE DE PARED RETIRO DEL PLATO DE MONTAJE Abra la caja y vuelva a doblar las cuatro lengüetas de la caja completamente contra los costados de la caja. Retire los siguientes artículos de la gomaespuma Montaje protectora: instrucciones de instalación, filtros,...
Page 36
Instrucciones de Instalación DETERMINACIÓN DE LA PLACA DE MONTAJE DEBAJO DE SU GABINETE Posición de la Placa – gabinete inferior Posición de la Placa – gabinete inferior hueco plano Las Lengüetas Las lengüetas de la Placa de de la Placa de Montaje Tocan la Montaje Tocan la Estructura Inferior...
Page 37
Instrucciones de Instalación ALINEE LA PLACA DE MONTAJE 30” Hole B Dibuje una Línea Agujero A Vertical en la Pared desde el Centro a la Parte Superior del Gabinete Agujero C Hole D Área E PRECAUCIÓN Ranura Use guantes para evitar cortes de dedos en extremos puntiagudos.
Instrucciones de Instalación TIPOS DE INSTALACIÓN (Elija A, B o C) Este horno microondas está diseñado para ser adaptado NOTA: Seleccione el tipo de ventilación requerida a los siguientes 3 tipos de ventilación: para su instalación y proceda a dicha sección. A.
Instrucciones de Instalación RECIRCULACIÓN (Sin Conductos No Ventilados) VISIÓN GENERAL DE LA INSTALACIÓN A1. ADHERA LA PLACA DE MONTAJE A LA PARED A2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR Cooking A3. AJUSTE EL MOTOR DEL CALENTADOR Conveni ence Potato Popcorn...
Page 40
Instrucciones de Instalación AJUSTE EL MOTOR DEL AJUSTE EL MOTOR DEL CALENTADOR CALENTADOR (cont.) Retire los tornillos que sostienen la unidad del Paletas del Ventilador calentador y los tornillos que aseguran el plato calentador. Retire el plato calentador de la caja externa, deslizando la misma hacia la parte trasera del horno microondas y empujando hacia arriba.
Instrucciones de Instalación CÓMO INSTALAR EL FILTRO MONTE EL HORNO MICROONDAS DE CARBÓN Retire los 2 tornillos en la parte superior del horno microondas, justo arriba del panel de la rejilla, usando un destornillador Phillips. Si los dos tornillos no están accesibles, lea la sección A5. Abra la puerta.
Page 42
Instrucciones de Instalación A5 MONTE EL HORNO (cont.) INSTALACIÓN/ REEMPLAZO DEL FILTRO DE CARBÓN SIN Inserte 3 tornillos autoalineantes (1/4” – 28 x 2 ACCESO A LOS TORNILLOS ¼”) a través de los agujeros del gabinete superior SUPERIORES Y LA UNIDAD YA externo.
B2. Prepare el Gabinete Superior B3. Ajuste el Motor del Calentador B4. Instale el Adaptador del Escape B5. Monte el Horno Microondas B6. Conecte la Tubería Cookin g Conve nience Bevera ge Potato Popcor n Defros t Cook Time Reheat...
Instrucciones de Instalación AJUSTE EL MOTOR DEL USE LA PLANTILLA DEL CALENTADOR (cont.) GABINETE SUPERIOR PARA LA PREPARACIÓN DEL Gire 90° GABINETE SUPERIOR Es necesario que haga agujeros para los tornillos de soporte de la parte superior, un agujero lo suficientemente grande para que el cable de corriente Parte trasera pueda pasar, y un disyuntor lo suficientemente grande...
Instrucciones de Instalación MONTE EL HORNO MICROONDAS ENSAMBLE E INSTALE EL ADAPTADOR Plato Calentador Regulador PRECAUCIÓN A fin de evitar el riesgo de lesión personal (lesión en la espalda u otras lesiones debido a un peso excesivo del horno microondas) o daños sobre la propiedad, deberá contar con la ayuda de dos personas para Coloque el horno microondas en su posición instalar este horno microondas.
Page 46
Instrucciones de Instalación MONTE EL HORNO CONEXIÓN DEL MICROONDAS (cont.) CONDUCTO Inserte un tornillo autoalineante a través Conducto del Hogar del agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al tornillo por lo menos dos giros completos una vez que las roscas fueron colocadas.
C2. Adjunte la Placa de Montaje a la Pared C3. Prepare el Gabinete Superior C4. Ajuste el Calentador C5. Monte el Horno Microondas Cooki ng Conve nienc e Potato Bevera ge Popco rn Defros t Cook Rehea t Time Weight/T ime Timer...
Instrucciones de Instalación ADHIERA LA PLACA DE ADAPTACIÓN DEL CALEFACTOR MONTAJE A LA PARED (cont.) PARA EL ESCAPE EXTERIOR TRASERO Para usar tornillos con resorte: Espacio para Tornillos con Resorte 1 Retire el tornillo del motor del calentador que Superior al Grosor de la Pared sostiene el plato calentador sobre el horno Tuercas Mariposa microondas.
Page 49
Instrucciones de Instalación ADAPTACIÓN DEL CALEFACTOR MONTE EL HORNO MICROONDAS PARA EL ESCAPE TRASERO EXTERIOR (cont.) De forma suave vuelva a colocar el ventilador en la cavidad con la parte del escape del ventilador arriba y enfrentando la parte trasera de la unidad. PRECAUCIÓN A fin de evitar el riesgo de lesión personal (lesión en la espalda u otras...
Page 50
Instrucciones de Instalación MONTE EL HORNO MICROONDAS (cont.) Inserte un tornillo autoalineante a través del agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al tornillo por lo menos dos giros completos una vez que las roscas fueron colocadas. (Más tarde se ajustará...
Instrucciones de Instalación ANTES DE USAR EL HORNO MICROONDAS Asegúrese de que el horno microondas haya Lea el Manual del Propietario. sido instalado de acuerdo con las instrucciones. Retire todos los materiales de embalaje del MANTENGA LAS INSTRUCCIONES horno microondas. DE INSTALACIÖN PARA USO DEL INSPECTOR LOCAL.
Page 52
Instrucciones de Instalación Impreso en China...
Need help?
Do you have a question about the JVM3160DFBB and is the answer not in the manual?
Questions and answers