Related Manuals for Huck International Howmet Aerospace SF20 Series
Summary of Contents for Huck International Howmet Aerospace SF20 Series
-
Page 1: Table Of Contents
SF20 Series SF20 & SF20N Bobtail Hydraulic Installation Tool ® Instruction Manual Table of Contents Declaration of Conformity Safety Instructions Tool Specifications Optional Equipment Principle of Operation Preparation for Use Tool-to-Powerig® Setup Pressure Settings Operating Instructions Maintenance Sticker Locations Nose Assembly Installation Tool Assembly &... -
Page 2: Declaration Of Conformity
• Supply of Machinery (Safety) Regulations 2008 Representatives: Paul Carson, Huck International, Ltd. Unit C Stafford Park 7, Telford Shropshire TF3 3BQ, England, United Kingdom Lutz Baumann, Hildesheim Operations, Fairchild Fasteners Europe - VSD GmbH, Steven 3, 31135, Hildesheim, Germany... - Page 3 SF20 BobTail® Hydraulic Installation Tool (HK1179) DANGER - IMPORTANT DO NOT EXCEED HOSE MINIMUM BEND RADIUS Failure to heed the warnings below could lead to a damaged hose, damaged tool, damaged property, personal injury, or death. • This high pressure hose is not to be used other than assembled in a genuine HUCK tool or hose assembly or used as a replacement hose of a genuine HUCK tool or hose assembly.
-
Page 4: Safety Instructions
SF20 BobTail® Hydraulic Installation Tool (HK1179) Safety Instructions I. GENERAL SAFETY RULES: II. PROJECTILE HAZARDS: 1. A half hour long hands-on training session with quali- fied personnel is recommended before using Howmet 1. Risk of whipping compressed air hose if tool is equipment. - Page 5 SF20 BobTail® Hydraulic Installation Tool (HK1179) Safety Instructions V. ACCESSORIES HAZARDS: ed tool as recommended to prevent an unnecessary 1. Disconnect tool from energy supply before changing increase in noise. inserted tool or accessory. 6. If the power tool has a silencer, always ensure it is in 2.
-
Page 6: Tool Specifications
SF20 BobTail® Hydraulic Installation Tool (HK1179) Specifications Hose Kits: Use only genuine HUCK Hose Kits rated at 10,000 psi working pressure. Hydraulic fluid: Hydraulic fluid shall meet DEXRON III, DEXRON VI, MERCON, Allison C-4 or equivalent ATF specifications. Fire resistant fluid may be used if it’s an ester based fluid such as Quintolubric HFD or equivalent. Water based fluid shall NOT be used as serious damage to equipment will occur. -
Page 7: Principle Of Operation
SF20 BobTail® Hydraulic Installation Tool (HK1179) Principle of Operation The operator pushes the Tool’s Nose over the end of the After the fastener is fully swaged, the operator must fastener until the Tool’s Puller bottoms on the fastener. release the trigger, at which point the Tool’s Anvil is When the trigger is pressed, the Powerig®... -
Page 8: Tool To Powerig Setup
SF20 BobTail® Hydraulic Installation Tool (HK1179) Tool to Powerig Setup WARNINGS: To prevent tripping hazard, suspend tools and route hoses off of floors. Only use compatible equipment with this tool. 1. Set Pull and Return pressures on Powerig® using Huck 5. -
Page 9: Operating Instructions
SF20 BobTail® Hydraulic Installation Tool (HK1179) Operating Instructions FOR SAFE OPERATION, THIS SECTION MUST BE READ AND UNDERSTOOD. Figure 3 Flange DOWN Bead UP Do NOT pull a fastener Do NOT install a fastener without a CORRECT CORRECT with the collar upside workpiece (structure to be fastened), a pin, down. -
Page 10: Maintenance
SF20 BobTail® Hydraulic Installation Tool (HK1179) Maintenance damage to O-Rings. (LUBRIPLATE 13O-AA is available in a tube as Huck P/N 502723.) Each Service Kit contains WARNING: Inspect tool for damage or wear perishable parts for your specific tool. Plan ahead and before each use. -
Page 11: Nose Assembly Installation
SF20 BobTail® Hydraulic Installation Tool (HK1179) Nose Assembly Installation and Removal - SF20 Figure 6 Figure 5 General Installation Nose Components General Cutter Nose Components Swaging Anvil Assembly Cutting Anvil Setscrews Puller 128807 Puller Lock Nut Anvil Holder 99-7881 shown 99-7881CX shown ATTACHING INSTALLATION NOSE ASSEMBLY: REMOVING CUTTER NOSE ASSEMBLY:... - Page 12 SF20 BobTail® Hydraulic Installation Tool (HK1179) Nose Assembly Installation and Removal - SF20N Figure 7 Figure 8 Extended Cutter Nose Components Extended Installation Nose Components Anvil Assembly Puller Anvil Holder Puller Extension Set screws Anvil Anvil Holder Puller Extension Puller 99-7880X-3 shown 99BT-M12-CLAT shown ATTACHING INSTALLATION NOSE ASSEMBLY:...
-
Page 13: Tool Assembly & Disassembly
SF20 BobTail® Hydraulic Installation Tool (HK1179) Tool Disassembly Procedure WARNING: Be sure to disconnect tool electrical control trigger system from Powerig® Hydraulic Unit BEFORE disconnecting tool’s hydraulic hoses from unit. If not disconnected in this order, severe personal injury may occur. Disassemble only the components necessary to check 7. -
Page 14: Components Drawings
SF20 BobTail® Hydraulic Installation Tool (HK1179) Tool Components SF20/SF20N... -
Page 15: Troubleshooting
SF20 BobTail® Hydraulic Installation Tool (HK1179) Troubleshooting Always check the simplest possible cause of a malfunction first. For example, a loose or disconnected trigger line. Then proceed logically and eliminate each possible cause until the defect is found. Where possible, substitute known good parts for suspected defective parts. -
Page 16: Limited Warranty
Huck Installation Equipment: conditions detailed in the product literature. Huck International, Inc. reserves the right to make changes 90 Day Limited Warranty on Nose Assemblies and in specifications and design and to discontinue models Accessories: without notice. - Page 17 SF20 BobTail® Hydraulic Installation Tool (HK1179) Notes...
- Page 18 Howmet Inc. (NYSE: ARNC) creates breakthrough products that shape industries. Working in close partnership with our customers, we solve complex engineering challenges to transform the way we fly, drive, build and power. Through the ingenuity of our people and cutting-edge advanced manufacturing, we deliver these products at a quality and efficiency that ensures customer success and shareholder value.
Need help?
Do you have a question about the Howmet Aerospace SF20 Series and is the answer not in the manual?
Questions and answers