Related Manuals for Huck International SFBTT8 Series
Summary of Contents for Huck International SFBTT8 Series
- Page 1 NSTRUCTION ANUAL SFBTT8 SFBTT8 SFBTT8-12 SFBTT8-12 BOBTAIL ® T OOLS 12-05-2013 HK1108...
-
Page 2: Ec Declaration Of Conformity
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS... -
Page 3: Table Of Contents
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS ONTENTS ONTENTS EC D ......2 ECLARATION OF ONFORMITY . -
Page 4: Safety
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS AFETY NSTRUCTIONS AFETY NSTRUCTIONS GLOSSARY OF TERMS AND SYMBOLS: III. OPERATING HAZARDS: 1. Use of tool can expose the operator’s hands to hazards including: crushing, Product complies with requirements set forth by the rele- impacts, cuts, abrasions and heat. -
Page 5: Principle Of Operation
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS RINCIPLE PERATION RINCIPLE PERATION The operator pushes the Tool's Nose over the end of the After the fastener is fully swaged, the operator must fastener until the Tool's Puller bottoms on the fastener. release the trigger, at which point the Tool's Anvil is ejected When the trigger is pressed, the rig receives a signal to off of the collar and the Tool is released from the fastener. - Page 6 SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS REPARATION REPARATION ® CAUTION: Do not use TEFLON * tape on WARNINGS: Read full manual before using tool. pipe threads. Pipe threads may cause tape to shred resulting in tool malfunction. Slic- A half-hour training session with qualified ®...
-
Page 7: Operating Instructions
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS PERATING NSTRUCTIONS PERATING NSTRUCTIONS For safe operation. Please read completely General 4. Push nose assembly onto the pin until the nose Operators should receive training from qualified assembly puller stops against the pin. Tool and personnel. -
Page 8: Tool To Powerig Set - Up
PULL Pressure Setting RETURN Pressure Setting 3/8 inch 6000 psi (414 bar) 3400 psi (234 bar) 3/8 inch 7250 psi (500 bar) 4150 psi (286 bar) Figure 1 SFBTT8 series Tool Nose Optional Assembly Hose Assembly CAUTION CAUTION TOOL 1... -
Page 9: Sticker
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS TICKER OCATIONS TICKER OCATIONS This tool comes labeled with important stickers that contain safety and pressure settings information. It is neces‐ sary that these stickers remain on the tools and are easily read. If stickers become damaged or worn, or if they have been removed from the tool, they must be replaced. -
Page 10: Maintenance
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS AINTENANCE AINTENANCE CAUTIONS: REVENTIVE AINTENANCE - Consult MSDS before servicing tool. System Inspection - Keep dirt and other material out of Operating efficiency of the tool is directly related to the hydraulic system. -
Page 11: Tool Assembly Drawings
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS Figure 2 SFBTT8 SFBTT8... - Page 12 SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS Figure 3 SFBTT8-12 SFBTT8-12...
-
Page 13: Replacing Puller And Anvil
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS EPLACING ULLER NVIL EPLACING ULLER NVIL NOTE: Applying an anti-seize lubricant to outside of Puller and inside of Anvil may improve Puller and Anvil life. REMOVAL INSTALLATION 1. Using an Allen wrench, remove Screw (504300) 1. -
Page 14: Optional Equipment
SFBTT8 Alcoa Fastening Systems (HK1108) SERIES YDRAULIC NSTALLATION OOLS PTIONAL QUIPMENT PTIONAL QUIPMENT To maintain CE conformity, only CE compatible equipment should be used with these tools. Installation tools and nose assemblies are the only CE components unless otherwise noted. Controls and other hardware shown in the manual are for domestic use only. - Page 15 WARRANTIES AS TO MERCHANTABILITY OR AS NSTALLATION QUIPMENT TO THE FITNESS OF THE TOOLING, OTHER Huck International, Inc. reserves the right to make ITEMS, NONSTANDARD OR CUSTOM MANUFAC- changes in specifications and design and to discontin- TURED PRODUCTS FOR ANY PARTICULAR PUR- ue models without notice.
- Page 16 For the Long Haul ™ One Great Connection A Global Organization industrial and Aerspace centers, where they provide Alcoa Fastening Systems (AFS) maintains company a ready source of AFS fasteners, installation tools, offices throughout the United States and Canada, tool parts, and application assistance. with subsidiary offices in many other countries.
Need help?
Do you have a question about the SFBTT8 Series and is the answer not in the manual?
Questions and answers