Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ESCO Technologies ETS-LINDGREN EMCenter EM8
Summary of Contents for ESCO Technologies ETS-LINDGREN EMCenter EM8
- Page 1 EMCenter™ EM8 Modular Test System Model 7000-013 Product Manual...
-
Page 2: Copyright And Trademark
Copyright and Trademark ETS-Lindgren Inc. reserves the right to make changes to any products herein to improve functioning or design. Although the information in this document has been carefully reviewed and is believed to be reliable, ETS-Lindgren Inc. does not assume any liability arising out of the application or use of any product or circuit described herein;... -
Page 3: Safety Information
Safety Information High Voltage: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury or death. Protective Earth Ground (Safety Ground): Indicates protective earth terminal. You should provide uninterruptible safety earth ground from the main power source to the product input wiring terminals, power cord, or supplied power cord set. -
Page 4: Table Of Contents
Table of Contents Copyright and Trademark ....................ii Revision Record ........................ii Safety Information ....................... iii Notes, Cautions, and Warnings ..................iii Table of Contents ....................4 Introduction ......................5 Product Features ......................... 5 8-Slot Example Application ................... 6 Operation ......................8 Installation ........................... -
Page 5: Introduction
Introduction ETS-Lindgren's EMCenter™ EM8 is the latest member of the EM family of products capable of significantly higher data collection speeds. The EMCenter™ EM8 Modular Test System forms the heart of many different EMC and RF test systems. The EMCenter has the ability to store up to eight (8) instrument plug-in cards, which can all be controlled and used simultaneously. -
Page 6: 8-Slot Example Application
8-Slot Example Application The international standard ISO11451-5 vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy – part 5: reverberation chamber describes the measurement of E-fields at eight reference points as part of the immunity test in a reverb chamber. For this application, the EMCenter EM8 can be configured with eight EMSense laser powered E-field probes, allowing the fast and accurate measurement of the isotropic field strength within the working volume of the chamber. - Page 7 Figure 3: Probes inside the chamber connected to the EM8 Figure 4: ISO11451-5 vehicle test of EM8 in TILE! EMCenter User Manual | 7 of 16 ets-lindgren.com...
-
Page 8: Operation
Operation Installation CAUTION: Before connecting any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. WARNING: Always unplug the unit before starting maintenance to prevent electrical shock. Maintenance includes removal of the plug-in cards or the top panel. -
Page 9: Interface And Cable Setup
5. Secure the card by tightening the four previous screws using a Pozi type screwdriver head PZ1. 6. Plug the interlock into the connector on the back of the EMCenter. 7. Connect the desired device(s) to the correct plug-in card. 8. - Page 10 Power Button How long you press the power button determines which function is used: • ON/OFF (1 sec) To power ON the EM8, press and hold the power button for one second until the LED ring around the button lights up in white. After a brief moment, the LED ring will begin flashing, indicating the booting process.
- Page 11 LASER Button When the EM8 is equipped with plugin cards, including one or multiple plugin cards containing lasers, the LASER ON button takes on a critical role. Its primary function is to activate the lasers safely simultaneously on all installed plugin cards. To maintain safety standards, initiating the laser power in the plugin cards follows a twostep process: entering a designated 'laser code' and manually activating the lasers.
-
Page 12: Back Panel
Back Panel Mains Plug the power supply cable into the mains inlet of the EM8, power the system by toggling the mains switch located beneath the mains inlet. Ethernet There is no display, so everything is controlled exclusively via the Ethernet connection. Therefore, an Ethernet cable must be connected to the rear of the EM8 and your network for proper functionality. -
Page 13: Network Configuration
Network configuration The EM8 is factory configured with standard static Ethernet addresses: Slot number IP Address Port number EM8 system 192.168.1.200 Slot 1 192.168.1.201 27531 Slot 2 192.168.1.202 27531 Slot 3 192.168.1.203 27531 Slot 4 192.168.1.204 27531 Slot 5 192.168.1.205 27531 Slot 6 192.168.1.206... - Page 14 1. Open PuTTY. 2. On the left menu select “Terminal”: a. Enable “Implicit CR in every LF” and “Implicit LF in every CR” to automatically send a Carriage Return after every Line Feed and vice versa. 3. On the left menu select “Session”: a.
-
Page 15: Specifications
Specifications Physical Specifications Height: 132 mm (5.2 in)(3U) Width: 19 in rack mountable Depth: 312 mm (12.3 in) excluding rear panel Weight: ~15.4 lbs. (7kg) empty Environmental Specifications Temperature Range: 0°C to 40°C (32°F to 104°F) Relative Humidity: 5% to 95% (non-condensing) Power Specifications Supply Voltage: 115/230 VAC... -
Page 16: Appendix A: Ec Declaration On Conformity
Appendix A: EC Declaration on Conformity ETS-Lindgren Inc. declares these products to be in conformity with the following standards and provisions: Product EMCenter Modular RF Platform Models: Directives: EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU RoHS Directive: 2015/863/EU Emission: EN 61326-1:2013, Class A1 Electrical equipment for measurement, control and laboratory use.
Need help?
Do you have a question about the ETS-LINDGREN EMCenter EM8 and is the answer not in the manual?
Questions and answers