Summary of Contents for Huntron PROTRACK SCANNER I
Page 1
Copyright 2005 Huntron, Inc. All rights reserved. Huntron, Tracker, ProTrack, Sig Assist and Huntron Access are registered trademarks of Huntron, Inc. All other names are trademarks or registered trademarks of their respective companies. This document may not be copied in whole or in part, or otherwise reproduced except as specifically permitted under U.S.
Page 2
Products purchased in the United States are to be returned to Huntron, Inc. at its factory, transportation prepaid. Products purchased outside the United States are to be returned to the source of purchase for warranty repair.
TYPICAL APPLICATIONS..............2-4 EXTERNAL CLEANING ............... 2-5 STORAGE INSTRUCTIONS ..............2-5 LIST OF ILLUSTRATIONS Figure Description Page Huntron ProTrack Scanner I and ProTrack I........... 1-1 External Features ..................2-2 Typical Applications ................2-4 LIST OF TABLES Table Description Page ProTrack Scanner I Specifications ............
INTRODUCTION AND SPECIFICATIONS 1-1. INTRODUCTION The Huntron ProTrack Scanner I, shown in Figure 1-1, has been designed as a compatible interface for the Huntron ProTrack I Model 20. Together, they create an effective test system for component troubleshooting. The ProTrack Scanner I allow faster comparison...
INTRODUCTION AND SPECIFICATIONS 1-2. SPECIFICATIONS The specifications for the ProTrack Scanner I are listed in Table 1-1. Table 1-1. ProTrack Scanner I Specifications ELECTRICAL Interconnections: Channels Number........2 Pins Test..........64 per channel Common........64 per channel Connectors IDC ..........64 pins each channel ZIF ..........40 pins each channel...
INTRODUCTION AND SPECIFICATIONS 1-3. SAFETY CONSIDERATIONS Safety Terms and Symbols Terms in this Manual. These terms may appear in this manual: WARNING Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION Caution statements identify conditions or practices that could result in damage to this product or other property.
Page 8
Do Not Operate With Suspected Failures. If you suspect there is damage to this instrument, have it inspected by qualified service personnel. Do Not Operate in Wet/Damp Conditions. Do Not Operate in an Explosive Atmosphere. Keep Product Surfaces Clean and Dry. Huntron ProTrack Scanner I...
INTRODUCTION AND SPECIFICATIONS WEEE and RoHS Status We, at Huntron are aware of the recycling needs for Waste Electronic and Electrical Equipment (WEEE) and Restriction of certain Hazardous Substances (RoHS) and are co-operating with systems established, worldwide for the collecting and recycling of our products.
This section describes the basic operation of the ProTrack Scanner I. Throughout the rest of this manual the ProTrack Scanner I will be referred to simply as the Scanner I. Take time to read this section carefully so that you can take full advantage of all its capabilities.
Before you begin to use the Scanner I, please take a few minutes to familiarize yourself with the instrument. All of the externally accessible features are shown in Figure 2-1 and summarized in Table 2-1. Figure 2-1. External Features Huntron ProTrack Scanner I...
Page 13
Scanner I. Any substitution may damage your instrument and/or result in an unsafe condition. Refer to the following diagram (see next page) to connect the ProTrack Scanner I to a ProTrack I Model 20. Operation Manual...
OPERATING INSTRUCTIONS 2-4. SETUP Note: User should take ESD precautions (wear ground straps) before operating the unit. The following procedure details how to setup and operate the Scanner I with a ProTrack for in-circuit comparisons of a 16 pin IC on different boards. Although other modes can be used with the Scanner I, this procedure is the one most commonly used for troubleshooting.
Page 16
ProTrack I manual). In this case you do not need to connect to the common of each board using the common test leads from the ProTrack’s common front panel jack. The common is routed through the Scanner I’s internal relays and out the 64 pin IDC cables. Huntron ProTrack Scanner I...
Page 17
OPERATING INSTRUCTIONS The topics that follow clarify various points and expand into other areas. CIRCUIT SIMILARITY - Devices and circuits being compared should be as nearly identical as possible, otherwise differences may be present which could give misleading signatures. Try to use the same PCB revision level when comparing boards or verify by schematic diagram that the device being examined is wired the same on boards of different revision level.
Should the Scanner I case require cleaning, wipe the instrument with a cloth that is lightly dampened with water or mild detergent solution. 2-7. STORAGE INSTRUCTIONS For optimum protection, store unit indoors in a dry place. Huntron ProTrack Scanner I...
Need help?
Do you have a question about the PROTRACK SCANNER I and is the answer not in the manual?
Questions and answers