Download
Share
Print this page
Pillar Booth Assembly Manual
  1. Manuals
  2. Brands
  3. Pillar Manuals
  4. Indoor Furnishing
  5. Booth
  6. Assembly manual

Pillar Booth Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Assembly Manual
The Pillar Booth

Advertisement

loading
Need help?

Need help?

Do you have a question about the Booth and is the answer not in the manual?

Questions and answers

Related Manuals for Pillar Booth

Summary of Contents for Pillar Booth

  • Page 1 Assembly Manual The Pillar Booth...

  • Page 2: Before You Start

    Before you start: 1. Assemble near an outlet 2. Assemble where you want the booth, so you don’t have to move it What you need: 1. 3 people able to lift ~ 50 lbs 2. Allen wrench (included) or a Hex screwdriver...
  • Page 3 What’s Included Hardware Desk Note: (F) Seismic Hardware is optional for use with seismic install only. Base and Ceiling Walls • • ·I □□□□□□□□□□□□□□ □□□□□□□□□□□□□□ eooooooooooooo□OO□□ooooooooooooe 00000000000000 ooocoooooooooo Door Left Back Right...
  • Page 4 Note: For seismic anchoring, skip steps #1 and #2 and refer to the Note: The vent should be on the left side of the booth included Seismic Installation Guide. when you are looking into the booth from the outside.
  • Page 5 A. Locate the back wall and remove the bottom acoustic panel. Just pull the panel, it is velcroed in place. Install the back wall Note: The panel is already removed with factory packaging. B. Locate the pins protruding from the bottom edge of the back wall and lower them into the pinholes in the back edge of the base.
  • Page 6 Before you start: Locate the right side wall and make sure the arrow stickers on the side of the wall are facing up. A. Notice the slits in the base. Drop the pins on the bottom of the Install the right side wall right side wall into the slits in the base.
  • Page 7 Install the left side wall Before you start: Locate the left side wall and make sure the arrow stickers on the side of the wall are facing up. A. Remove botttom acoustic panels. Just pull the panels, they are velcroed in place. B.
  • Page 8 Install the ceiling Before you start: Be sure the light is on the left side. Once the booth is built the floor and ceiling vents should be on opposite sides. A. Two people should lift the ceiling over their heads and walk it into the booth, lifting it up over the walls while guiding it into place.

  • Page 9: Install The Door

    “L” channels of the back wall and the door. Note: You can now enter the booth. If you need to adjust anything you can go inside the booth and gently pop the ceiling up where it is not aligned...
  • Page 10 B. Bolt the door to the ceiling and base • Open the door and screw in an (A) bolt through each of the two holes at the top of the door frame. Bolt the door • Screw in an (A) bolt through each of the two holes at the bottom of the door frame.
  • Page 11 Bolt the ceiling A. Bolt the ceiling to the side walls by locating the pins protruding through the slits in the ceiling and screwing a (C) bolt into each of the four pins. B. Bolt the back wall to the ceiling by screwing a (B) bolt into each of the two holes at the top of the back wall.
  • Page 12 Connect the electrical First, locate the three wires coming out of the back left corner of the ceiling and Second, locate the two wires coming the three wires coming out of the top left out of the back left corner of the base corner of the back wall - they are each color and the two wires coming out of the coded.
  • Page 13 Plug in your booth and Tighten all 20 bolts pause distractions The fans and light will turn on as soon as the door is opened.
  • Page 14 Install the desk On the left side wall there are three sets of open notches on either side of the acoustic panel. Decide which height you want the desk • Top Notches: Standing OR Bar-height stool • Middle Notches: Counter-height stool •...
  • Page 15 1. Place the included seismic anchoring template on the floor A. Locate the seismic anchoring template. B. Place it on the floor where you want the booth and secure it in place with tape. 2. Bolt the seismic plates to the floor A.
  • Page 16 Sprinkler System Installation: 1. Remove the inside cover plate A. From inside the booth, locate the round cover plate on the underside of the ceiling. It is between the light and the back wall. B. Twist the cover plate counter clockwise until it is completely removed.
  • Page 17 Step into a Pillar Booth and pause distractions. Pillar Designs LLC | pillarbooth.com | sales@pillarbooth.com © 2023 Pillar Designs LLC. All rights reserved.