Subscribe to Our Youtube Channel
Related Manuals for Duplomatic 10 Series
Summary of Contents for Duplomatic 10 Series
- Page 1 DM16 Turret series DIRECT DRIVE MOTOR TURRETS INSTRUCTIONS FOR USE AND MAINTENANCE M.I. 6458-16 01-10 ISSUED...
- Page 2 This symbol points out possible danger due to electricity. GENERAL RULES • The tool turrets of Duplomatic design are provided for being incorporated in numerically controlled turning machines, and they must be used only for this purpose.
-
Page 3: Table Of Contents
INDEX sheet 1. SUPPLY COMPOSITION ..................... 4 2. TURRET IDENTIfICATION ..................5 3. CHARACTERISTICS AND PERFORMANCES Technical data ......................6 Loading capacity ......................6 Duty performances ..................... 7 Overall dimensions ....................8/9 Tool disc interface specs ..................10 Direct motor driver ....................11 4. INSTALLATION 4.1 Box removing and lifting ................... -
Page 4: Supply Composition
1 - SUPPLY COMPOSITION HYDRAULICPOWER PACK SUPPLY Fuses MACHINE ELECTRICAL CABINET DUPLOMATIC SUPPLY DM-16 Direct drive motor turret. TMC- Direct motor driver for remote installation into the machine electrical cabinet. (See electrical manual E.M. TMC- AT CUSTOMER CHARGE Installation of the Direct motor driver into the Electrical Cabinet and Electrical connections between turret, driver, and CNC. -
Page 5: Turret Identification
2 - TURRET IDENTIfICATION 2.a - Turret name plate The details for turret identification are printed on a name plate fixed on turret housing. Serial Nr. Code Nr. Model COD. [ V ] Electric supply (Left version) (Right version) 2.b - Model identification DM - OPTIONALS CODE SUPPLY VOLTAGE 400 VAC - 3 SIZE CODE... -
Page 6: Characteristics And Performances
3 - CHARACTERISTICS AND PERFORMANCES 3.1 - Technical data DM-16 Size Tool stations N° 8÷12 Inertia of transportable masses Positioning times: one step index time 30° 0,18 0,23 (acc. / dec. included) 45° 0,22 0,29 180° 0,52 0,60 step-less rotation time 30° 0,067 0,067 45° 0,10 0,10 Unclamping time 0,14 Clamping time... -
Page 7: Duty Performances
3.3 - DM-16 Duty performances [N] Tangential force 200000 100000 80000 60000 40000 20000 1− 10000 8000 6000 4000 2000 1000 [mm] The diagram refers to F values which cause elastic yelding within the rates shown in the schedule. [N] Tilting force (to push) [N] Tilting force (to lift) 200000 100000 80000 60000 40000... -
Page 8: Overall Dimensions
3.4 - DM-16/10 Overall dimensions 3.4.a - DM-16/10 Right version 20° 20° M8x15 Ø A1 - B1 1/4" GAS (Additional ports) CONNECTORS N°2 M10 (for lifting) "A" view BACK VIEW for M10 TOOL DISC INTERFACE (10) R - 1/4" GAS OR 2050 ø10 ø10 A - B 1/4" GAS + 0,003 ø40 –... - Page 9 3.4.b - DM-16/10 Left version A - B 1/4" GAS 20° 20° M8x15 Ø R - 1/4" GAS CONNECTORS N°2 M10 (for lifting) BACK VIEW for M10 TOOL DISC INTERFACE (10) OR 2050 ø10 ø10 + 0,003 ø40 – 0,005 ø16 ø110 1) Inlet coolant position. 7) Hydraulic connections.
-
Page 10: Tool Disc Interface Specs
3.5 - DM-16 Tool disc interface specs α (max ±20°) 45° INLET COOLANT POSITION max.9 Ø Ø ±0,1 Ø + 0,003 - 0,005 9 max Ø Ø 0,015 0,015 FOR SCREWS M8 (1) Ø 110 (FOR PINS Ø M.I.6458-16-0110... -
Page 11: Direct Motor Driver
3.6 - Direct motor drive TMC- 3.6.a - Overall dimensions and fixing WARNING: Foresee at least 20 mm of free space on both sides and al least 100 mm above and below to allow cooling airflow. For M5 NOTE: For electrical connections, installation of the Direct motor driver into the machine electrical cabinet, and interfacing to CNC, see electrical Manual E.M. TMC- M.I.6458-16-0110... -
Page 12: Installation
4 - INSTALLATION 4.1 - Box removing and lifting Nr. 2 Eyebolt M10 TURRET WEIGHT (without tool disc) 62 Kg. Fig. 1 M.I.6458-16-0110... -
Page 13: Turret Placing On The Machine
4.2 - Turret placing on the machine Make sure the fixing surface is clean and squared to ensure a proper tool alignment. Usually to bring the turret axis to the machine axis an adaptor plate (B) must be foreseen. Fix the turret to the machine's slide (A) by means of 8 appropriate screws (C) (high-resistant screws according to class 12.9 DIN 912) and make sure that between the screw head and the turret the respective washer (D) of appropriate thickness (8 mm) has been inserted. The reference pin (E) which is supplied together with the turret, is normally located at the opposite side of the working tool. Align the front surface of the disc in order to have it perpendicular to the spindle axis. Then lock the screws according to the torque rates shown in the table. In case of crash the turret may slip and turn around the reference pin. In this way any subsequent re-alignment will be facilitated. øD Screws Reference pin... -
Page 14: Coolant Operation
4.4 - Coolant operation (Fig. 4) The coolant circuit is designed for supply only the tool in working position and for set the valve (053) in different positions, ac- cording to the disc requirements. The coolant pipe coming from the pump must be connected to the "R" inlet on the turret housing. Throught an internal path the coolant passes from the housing to the (044) manifold ring that, by means of an anular groove brings it to the exit point 1. The coolant valve (053) slides on the rear surface of ring (046), which rotates as one piece with the turret ring and the disc, let the coolant flow to the working tool area. -
Page 15: Hydraulic Connections
4.5 - Hydraulic connections (Fig. 5) Safety valve (~ 0,5 bar) V= 2 l P= 40 bar Q= 4 l/min HYDRAULIC POWER PACK (Example) (1) IMPORTANT: A flow adjustment valve must be foreseen in order to avoid a violent or noisy clamping. (2) The accumulator's volume is according to the real pump flow rate. -
Page 16: Wiring Diagram And Electrical Connections
4.6 - Wiring diagram and Electrical connections (Fig. 6-7 and 8) The DM turrets are supplied with a proper Direct motor driver for remote installation inside the machine electrical cabinet. The turret-side electrical connections are carried-out by connectors. IMPORTANT : In the machine electrical cabinet proper electrical protection devices must be foreseen. (i.e. fuses). For all details and specs about electrical connections and interfacing to CNC, please refer to relevant Electrical Manual. - Page 17 +24 V DC CLAMPING SWITCH 0 V DC Terminal board (X1) - Power connector (Turret-side) Connector cable-side (not supplied) compatible with : SIEMENS 6FX2003-OCA10 (female) Connector cable-side (not supplied) compatible with : SIEMENS 6FX2003-OCE17 (female) (X2) - Signals connector (Turret-side) Fig.
-
Page 18: Assembly Drawings And Part Lists 5.A Main Section
5. DM-16/10 ASSEMBLY DRAWINGS AND PART LISTS 5.A - DM-16/10 Main section Ref. Description Code Q.ty Ref. Description Code Q.ty 020 Spring 0328496 Toothings 0432553 021 Nut BES 08-DM-1 0661346 022 Proximity 0661345 003 Screw M10x30 A12.9 0531293 023 Upper cover 0334050 004 Gasket 0592650 024 Screw M5x25 0530035 006 O-Ring OR 4325 0590607 025 O-Ring OR 4287 0590333... - Page 19 M.I.6458-16-0110...
- Page 20 5.A1 - DM-16/10 Main section (part. "D") 089 (clamp with Loctite 270) Part. "D" Fig. A1 Ref. Description Code Q.ty Ref. Description Code Q.ty Right rear flange 0334071 092 Resolver 0432593 Left rear flange 0334240 093 Screw M4x8 0530280 094 Washer 0333562 E1 version rear flange 0334417 095 Bearing 6006-2RS 0630165 085 O-Ring OR 3575 0591429 096 Snap ring 0550370...
-
Page 21: B Back View
5.B - DM-16/10 Back view LEfT VERSION RIGHT VERSION "E" View "E" View Fig. B Ref. Description Code Q.ty Ref. Description Code Q.ty 030 Power connector 0671398 036 Rivet 0530521 037 Terminal board 0491292 031 Screw M2,5x8 0531415 038 Screw M3x8 0530012 032 Signal connector 0671397 039 O-Ring OR 2031 0590165 033 Screw M2,5x6... -
Page 22: C Hydraulic Connections
5.C - DM-16/10 Hydraulic connections ( "E" view ) LEfT VERSION RIGHT VERSION "E" View "E" View Fig. C SEC. F-F PART LIST LEfT VERSION PART LIST RIGHT VERSION Ref. Description Code Q.ty Ref. Description Code Q.ty Plug 1/4" GAS 0570182 Plug 1/4" GAS 0570182 Washer 0570193 Washer 0570193 Fitting 90° (for ø10 mm tube) 0571637 Plug 1/4"... -
Page 23: D Coolant Circuit
5.D - DM-16/10 Coolant circuit LEfT VERSION RIGHT VERSION SEC. "E" SEC. G-G Fig. D Ref. Description Code Q.ty Ref. Description Code Q.ty 053 Coolant valve 0330380 Right coolant flange 0334232 054 O-Ring OR 2043 0590297 Left coolant flange 0334241 055 Spring 0319956 045 Screw M5x8 0531991 046 Coolant ring 0333493 056 O-Ring OR 114 0590172... -
Page 24: Recommended Spare-Parts
Lubricant amount Kind of lubricant Manufacturer CENTOPLEX KLÜBER DM-16 90 gr. GLP 500 LUBRICATION (code 0890102) (1) (1) This code is related to the required quantity. 7.2 Turret lubrication check WARNING: If oil leakage happens from safety valve (103) call Duplomatic Service Center. 7.3 Coolant valve check Every 2.500 ÷ 3.000 hours, check the condition of coolant valve (053) removing snap ring (059) and plug (058), and replace it, if necessary. (See para 4.4). M.I.6458-16-0110... -
Page 25: Extraordinary Maintenance
8 - EXTRAORDINARY MAINTENANCE 8.1 Replacing and adjusting proximity switch. The following sketch shows the electric lay-out in the turret and relevant switch. +24 V DC (Brown) CLAMPING SWITCH (Black) 0 V DC (Blue) 13 12 M.I.6458-16-0110... - Page 26 8.2 Turret clamping (3) proximity switch. (See para 5.A) (Clamping stroke) 3,5 CLAMPED TURRET UNCLAMPED TURRET WARNING : In case of intervention on proximity switch (3), the hydraulic unclamping line "B" must be depressurized. Verify that turret is correctly clamped on any position. Replacing proximity switch: 1) Remove the cover (1).
- Page 27 M.I.6458-16-0110...
- Page 28 DUPLOMATIC AUTOMATION S.r.l. e-mail: info duplomatic.it 20025 LEGNANO (MI) - ITALY P .LE BOZZI, 1 come visit Duplomatic homepage: PHONE 0331/472111 www.duplomaticautomation.com FAX 0331/455161...
Need help?
Do you have a question about the 10 Series and is the answer not in the manual?
Questions and answers