All LED ABG330/CCT Installation Manual

Safety
• Do not cover the ground contact.
• Do not cover the luminaire, hang or fasten anything from it.
• Do not operate if any visible damage can be seen to the product.
• Do not operate if any water ingress has occurred.
• Do not operate if any smoke, steam or crackling noises can be heard from the luminaire.
• Do not operate if any signs of overheating are recognised.
• Avoid installation in any areas where there is a risk of strong mechanical loads.
• Do not place any material over the lens or LED diode/chip.
• Do not insert objects into the luminaire.
• Do not clean using any solvent based abrasive or aggressive product.
• Do not pull any cables connected to the product.
• Do not direct the luminaire into a persons eyes, as this unit may have an intense light output, which if
incorrectly used may cause eye damage.
• Light engines/LEDs and other light sources may heat up, please take care when handling the products.
• The manufacturer will not be deemed liable or held responsible for any damages caused by faults or
manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this
device. Please refer to our troubleshooting guide for further information.
• The manufacturer will not be held liable for any death(s) or injuries caused by misuse or poor installation or
any unreported faults of this product version or versions thereof.
• LEDs are sensitive to electrostatic discharge. Do not touch the surface of the LED module.
• Do not connect to a temporary electricity supply, this may damage the electronics.
• Light fittings with an integrated emergency option are with a separate installation and wiring leaflet. Please
refer to this manual for further details. If the manual is unavailable please contact an All LED representative for
assistance.
• It is strongly recommended that a Residual-Current Device (RCD) is used with this product to minimise the
risk of electrocution.
• REPLACE DAMAGED PRODUCT IMMEDIATELY.
• Keep away from children.
Returns & Faulty Items
• If any problem is encountered during or after installation, please call All LED technical department to get the
problem resolved as soon as possible.
• Please do not just return the item to the outlet you purchased it from, as you are only entitled to a
replacement or refund after the unit has undergone testing and the unit has been confirmed as having a
manufacturing defect/fault. Your statutory rights are not affected.
• The manufacturer will not be deemed liable or held responsible for any damages caused by faults or
manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this
device. Please refer to our troubleshooting guide for further information.
• All installations must be carried out in accordance with this installation guide and user manual.
• All goods are supplied under the terms and conditions of All LED LTD, a copy of which may be obtained
upon written request.
Environmental Protection
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice.
This product supplied with a limited guarantee, subject to terms and conditions.
The manufacturer will not be deemed liable or held responsible for any damages
ISOLATE MAINS SUPPLY
caused by faults or manufacturing defects that may be present in any of its products
BEFORE HANDLING ANY
or the misuse or incorrect installation of this device
ELECTRICAL PRODUCTS
Your statutory rights are not affected.
• This product may need to be installed by a qualified electrical installer.
• Please read this guide in its entirety to fully understand the products before attempting any install.
• All electrical work should be completed in accordance with the latest IET regulations, and/or any other relevant rules, regulations or laws of the
country in which it is being installed.
• The item must be installed in isolation from any insulating material and is adequately ventilated to prevent premature failure.
• Ensure power supply is isolated prior to installation, maintenance or performing any other form of electrical work.
• In the event of incorrect or improper function with specific regard to any of ALL LED's products contact ALL LED for further advice.
SAFETY WARNING
• ENSURE THE PROTECTIVE PLASTIC PLATE LOCATED ON TOP OF THE LED'S IS NEVER REMOVED OR TAMPERED WITH.
• IF THERE IS ANY VISIBLE DAMAGE TO THIS ITEM, PLEASE ENSURE THAT THE POWER IS SWITCHED OFF AND REMAINS OFF.
• DO NOT TOUCH THE LED CHIPS AT ANY POINT DURING, OR AFTER INSTALLATION OF THE LUMINAIRE AS THERE IS RISK OF
ELECTRICAL SHOCK.
Technical Specifications
Product Code
Luminous Flux (LM)
Useful Luminous Flux (LM)
CCT (Kelvin)
Beam Angle (°)
SDCM
CRI
Peak Intensity (cd)
Operating Voltage (V)
Max Output Power (W)
Operating Current (A max)
Standby Power (W)
Power Factor (Pf)
Class
Body Material
Cut Out
Frame Colour
Switching Cycles
Ingress Protection
Ambient Operating
Temperature (°C)
Input Frequency (Hz)
Guarantee
ALL LED LTD
Dimmable
42 Sedgwick Road,
Cable Length
Luton, LU4 9DT
Life Time (L70 B50)
www.allledgroup.com
sales@allledgroup.com
Survival Factor
Tel: +44 (0)208 841 9000
Lumen Maintenance Factor
Displacement Factor
INSTALLATION GUIDE
ABG330/CCT/MS
ENSURE POWER SUPPLY IS OFF WHEN HANDLING ANY ELECTRICAL EQUIPMENT.
Driver Technical Specification
ABG330/CCT Operating Voltage
3000K - 1313lm / 4000K - 1436lm /
Max Output Power
6000K - 1346lm
Output Current (Max)
3000K - 1313lm / 4000K - 1436lm /
6000K - 1346lm
Output Voltage (Max)
3000K / 4000K / 6000K
PF
120
Efficiency %
<6
No Load Power (W)
>80
Dimmable
505
Class
39VDC
Body Material
13W
Frame Colour
335mA
Switching Cycles
≤0.5
Ingress Protection
>0.9
Ambient Operating Temperature (°C)
II
Input Frequency (Hz)
PC
Guarantee
N/M
Output Type
White
Life Time
30000
Sensor Technical Specification
IP65
Operating Voltage
-20°C ~ +40°C
Rated Load
50Hz
Stand-by Power
3 Years
Sensitivity
No
Hold-time
No
Daylight Sensor
Microwave Frequency
30000
Transmitting Power
>0.9
Detection Range
>0.7
Detection Angle
>0.9
Working Temperature
!
PLEASE READ
BEFORE USE!
240VAC
13W
335mA
39V
DF>0.9
87
≤0.5W
No
II
PC
White
30000
IP65
-20°C ~ +40°C
50Hz
3 Years
Isolated Driver
30000
220 ~ 240 VAC 50/60Hz
400W (Capacitive Load)
800W (Resistive Load)
<0.5W
10% / 50% / 75% / 100%
5s / 90s / 5min / 15min
2lux / 10lux / 50lux, disable
5.8 GHz +/- 75MHz
<0.2mW
Max (diameter x height): 10m x 6m
30° ~ 150°
-20°C ~ +60°C