Related Manuals for Hyundai power products HEL25SL
Summary of Contents for Hyundai power products HEL25SL
- Page 1 PETROL PRUNER HEL25SL WARNING: Read thoroughly the instruction manual before using.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY WARNINGS..........................3 2. YOUR PRODUCT........................... 8 3. ASSEMBLY............................. 9 4. FILLING THE FUEL TANK.........................11 5. OPERATION............................12 6. MAINTENANCE AND STORAGE..................... 18 7. DECLARATION OF CONFORMITY....................21 8. WARRANTY............................22 9. PRODUCT FAILURE........................... 23 10. WARRANTY EXCLUSIONS......................24... -
Page 3: Safety Warnings
1. SAFETY WARNINGS WARNING! When using this type of garden tool, basic precautions should always be followed to reduce the risk of fire, electric shock and injury. Read all instructions carefully before attempting to use this product and retain these ... - Page 4 Always inspect the machine before and after operation. If the tool is damaged or faulty, stop using the tool and bring it to an authorized service for inspection and repair. Turn off the tool after use, when you leave it unattended, when changing these accessories and before servicing.
- Page 5 should never be used. For the chainsaw designed with the chain guide on the left side, the reference to the "right hand" and "left hand" positions is reversed. When cutting a branch that is under stress, pay attention to the risk of elastic return. When the ...
- Page 6 During maintenance and storage Stop the tool and wait until it stops. Make sure all moving parts have come to a standstill. Allow the machine to cool before performing inspection, adjustments, maintenance, servicing and storage. Store the tool where fuel vapor will not reach a flame or spark. ...
- Page 7 Symbols Warning symbol. Read and refer to these operating instructions. WARNING: appropriate ear, eye and head protection must be worn. Value of sound emission according to European Directive 2000/14 / EC. Kickback：Never cut with the tip of the chainsaw. Do not operate the tool with one hand. Always hold it with both hands.
-
Page 8: Your Product
2. YOUR PRODUCT 2.1 DESCRIPTION 1- Front hand guard - Guard between the front handle and the saw chain for protecting the hand from injuries and aiding in control of the chain saw if the hand slips off the handle.This guard is used to activate the chain brake which is to stop the saw chain rotation. -
Page 9: Assembly
26-Guide bar cover - Device for covering the guide bar and saw chain during transport and other times when the chain saw is not in use. 2.2 TECHNICAL DATA Model HEL25SL Type of engine RY1E35F (air cooled 2-stroke petrol engine) Fuel Tank Volume 200cm³... - Page 10 4) Install the guide and mount the chain on the pinion and guide in the direction shown in the diagram. 5) Loosen the nuts and remove the chain cover. Attach the bracket to the back of the motor assembly with a screw. Install the guide and mount the chain on the pinion and guide in the direction shown in the diagram.
-
Page 11: Filling The Fuel Tank
While lifting the chain guide, turn the content screw to apply correct tension to the chain. Then lock the fastening nut. Rotate the chain with your hand to check that it is turning without excessive resistance and that it is properly tightened. Repeat the installation if the chain is not tight. -
Page 12: Operation
FILLING THE FUEL TANK Unscrew the fuel tank cap and remove it. Fill the tank slowly with the mixture. Do not exceed the maximum capacity (fill to 80% of its capacity preferably). Replace the cap on the fuel tank and tighten it ... - Page 13 Hold the chainsaw firmly against the ground. Put the chainsaw: Either on the left side of your body holding the handle firmly with your left hand. Use your right hand to pull the starter rope Either on the right side of your body holding the handle firmly with your right hand. Use your left hand to pull on the starter rope.
- Page 14 b.Chain brake The chain brake is a device that automatically stops the chain in case a backward movement occurs, causing the saw to jump. Normally, the brake is automatically activated by the inertia force. It is also manually tightened by pushing the brake lever down and forward. When the brake is running, a yellow sign comes out from the base of the brake lever.
- Page 15 5.4 WORK WITH WIRE AND HARNESS NOTE: It is necessary to have a complete training before working at high. It is strongly recommended that only experienced and trained persons carry out work at high. Know all emergency procedures to be carried out. These instructions are examples of good practice.
- Page 16 c. Starting the saw in the tree When starting the saw in the shaft, the operator should: 1. Apply the chain brake before starting, and 2. Hold the saw on the left side, either on the right side before starting: ...
- Page 17 e. Release of a jammed saw If the saw gets stuck during cutting, the operators should: 1. Saw the saw and attach it securely to the cutting foot of the shaft (ie trunk side) or has a separate chord from the tool 2.
-
Page 18: Maintenance And Storage
e. Pruning a tree Begin pruning by nicking the tree from below and then finish at the top. 6. MAINTENANCE AND STORAGE 6.1 MAINTENANCE Before any maintenance work, the machine must be switched off and completely cooled. Perform the maintenance work according to the instructions below and perform them regularly. - Page 19 c. Cleaning the oil inlet Disassemble the chain guide and the chain hood and check that the oil supply is clean. If dirty, remove dirt with a clean compressor or cloth. d. Cleaning the oil filter and fuel filter Clean these items regularly. Remove them from the tanks using clamps. Clean them with gasoline and then put them back in place afterwards e.
- Page 20 g. Spark plug Clean the electrodes with a wire brush and set the gap to 0.6mm if necessary. h. chain saw Check each time the cutter and cutting angles are as shown below. i. Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it).
-
Page 21: Declaration Of Conformity
32 rue Aristide Bergès - Z.I. du Casque - 31270 Cugnaux - France Declares that the machinery designated below: PETROL PRUNER Model: HEL25SL Serial number: 20231005663-20231005812 Complies with the provisions of the Directive "machinery" 2006/42/EC and regulations National transposing it;... -
Page 22: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 23: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 24: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the HEL25SL and is the answer not in the manual?
Questions and answers