Sealey KS1.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT
IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Risk of fall from the step.
‰
Ensure the step is suitable for the task.
9
The maximum number of users is 1.
9
Inspect the step after delivery. Before every use visually check the step is not damaged and is
9
safe to use.
Familiarise yourself with the step before use.
9
The step should not move when weight is applied.
9
Employers should ensure employees are competent using the equipment for work.
9
Ensure the base sits firmly on the floor before use.
9
Wear suitable non-slip footwear when using the step.
9
For outdoor use caution to the wind.
9
DO NOT use if damaged.
8
DO NOT exceed the maximum load of 150kg.
8
DO NOT position step on contaminated ground.
8
DO NOT use the step on an unlevel or unfirm base.
8
DO NOT overreach.
8
Move the step if necessary, or use alternative equipment if the step is unsuitable.
9
DO NOT use step to access heavy equipment stored at height.
8
DO NOT step off the side of step onto another surface.
8
DO NOT ascend or descend unless you are facing the step.
8
Avoid work that imposes a sideways load on step, such as side-on drilling through solid materials.
9
DO NOT carry equipment which is heavy or difficult to handle while using step.
8
DO NOT carry items in both hands when stepping onto the step.
8
DO NOT wear unsuitable footwear when climbing the step.
8
DO NOT use the step if you are not fit enough. Certain medical conditions or medication, alcohol
8
or drug abuse could make use of step unsafe.
DO NOT spend long periods on a step without regular breaks (tiredness is a risk).
8
Prevent damage of the step when transporting e.g. by fastening and, ensure they are suitably
9
placed to prevent damage.
DO NOT use the step if contaminated, e.g. with wet paint, mud, oil or snow
8
DO NOT use the step outside in adverse weather conditions, such as strong wind.
8
For professional use a risk assessment shall be carried out respecting the legislation in the country of use.
9
When positioning the step take into account risk of collision with the step e.g. from pedestrians, vehicles or doors. Secure doors
9
(not fire exits) and windows where possible in the work area.
9
WARNING! ELECTRICAL HAZARDS.
‰
Identify any electrical risks in the work area, such as overhead lines or other exposed electrical equipment and do not use the step
9
where electrical risks occur. Use non-conductive step for unavoidable live electrical work.
DO NOT use the step as a bridge.
8
DO NOT modify the step design.
8
DO NOT move a step while standing on it.
8
DO NOT use the equipment if the base is damaged and the step slips when under load.
8
2. INTRODUCTION
Heavy-duty construction with non-slip surface. Three spring loaded wheels allow step to glide over floor, yet sit down firmly on rubber
stops when load is applied.
3. SPECIFICATION
MODEL NO:
Base Size:
Material:
Maximum Capacity:
Step Heights:
Top Step Size:
© Jack Sealey Limited
KICK-STEPS
MODEL NO:
KS1.V2 KS2.V2
Steel with heavy non- Composite construction
slip rubber treads with non-slip surface
Ø430mm Ø430mm
Steel Composite
150kg 150kg
220, 420mm 220, 420mm
Ø280mm Ø280mm
Original Language Version
KS1.V2, KS2.V2
KS1.V2, KS2.V2 Issue 1 31/01/24