Related Manuals for LifeSafety Power Helix ATS HAC-8R
Summary of Contents for LifeSafety Power Helix ATS HAC-8R
- Page 1 Helix ATS PDU Installation Manual HELIX Power Distribution Unit / Automatic Transfer Switch HAC-8R LifeSafety Power, Inc. | PH 888.577.2898 | TechSupport@LifeSafetyPower.com P03-103 Rev A01...
- Page 2 Helix ATS Installation Manual Table of Contents...
-
Page 3: Notes And Warnings
Notes and Warnings Symbol Definitions is not achieved due to uneven mechanical loading. The following symbols are used throughout this manual Circuit Overloading - Consideration should be given to the connection of the equipment to the supply cir- This symbol is intended to alert the installer of shock cuit and the effect that overloading of the circuits hazards within the enclosure. - Page 4 Helix ATS Installation Manual Introduction Product Description Specifications The Helix ATS HAC-8R combines an Automatic Transfer Input voltage range 90 – 265 VAC Switch (ATS) with a network managed Power Distribution Input frequency 47 – 63 Hz Unit (PDU). Dual AC inputs allow the ATS to use a backup...
-
Page 5: Section 1 - Installation
Installation and Operation Section 1 – Installation The following pages cover the installation of the HAC-8R rack-mountable PDU. 1.1 Mounting the HAC-8R into a Standard 19" Rack Use the following procedure when mounting an HAC-8R NOTE: Use rails or other appropriate support for heavy PDU into a standard EIA 19"... - Page 6 Helix ATS Installation Manual 1.2 HAC-8R Power Distribution Unit Overview Figure 2: HAC-8R Front View No user serviceable parts inside refer servicing to qualified service personnel Aucune pièce interne ne peut être réparer Demandez l’assistance d’un technicien qualifié...
- Page 7 HAC-8R as follows: I2C Sensor Input 10 Seconds User Name & Password Only The I2C terminal accepts LifeSafety Power temperature or 20 Seconds User Name, Password, and IP Settings temperature/humidity sensors. NOTE - The user name and password will both reset to "ad- Fault Relay Output min".
-
Page 8: Section 2 - Initial Configuration
Helix ATS Installation Manual Section 2 – Initial Configuration The Helix ATX management interface allows users to configure, monitor, and control each output port of the HAC-8R power distribution unit. The Helix ATS uses an embedded web browser based interface and does not require the installation of any dedicated software on the user's PC. - Page 9 Installation and Operation Figure 7: HAC-8R Home Page...
- Page 10 Helix ATS Installation Manual 2.3 Configuring the TCP/IP Settings is power cycled, or rebooted. In the menu bar at the top of the browser screen, click the 2.4 Configuring the Time Settings "Configure" link. Figure 8 shows the top section of the HAC-8R The Time Settings block (See Figure 8) is where the time Configure page.
- Page 11 Installation and Operation form). Click the "Submit" button at the bottom of the "Basic" sec- v1 and v2 access. Multiple source networks can be added tion to save the settings, otherwise you will lose the settings. to the Security Name Settings block. Be sure to click the These settings will take effect after a reboot of the HAC-8R.
-
Page 12: Configuring The Email Settings
Helix ATS Installation Manual "Submit" button to save the settings, which will take effect after rebooting the HAC-8R. The SNMP Trap Receiver IP and Port settings should be set to the proper address for the SNMP Trap receiver. Click the "Submit"... - Page 13 Installation and Operation Figure 9: Middle Section of the HAC-8R Configure page...
-
Page 14: User Settings
Helix ATS Installation Manual 2.8 PDU Network Module Settings ADCX Upper Limit Enter an upper voltage limit for each ana- log voltage input. If the voltage measured goes ABOVE this There are many settings in the PDU Network Module Settings value, an alert will be triggered. - Page 15 Installation and Operation Figure 10: Bottom Section of the HAC-8R Configure Page...
- Page 16 Helix ATS Installation Manual 2.11 Certificate Settings 2.17 The Programming Page The HAC-8R allows a user-supplied certificate to be used. Clicking the Programming button on the home page brings Click the "Upload Certificate" button (Figure 10) to enter the up the output configuration screen. Figure 11 shows the Certificate screen.
- Page 17 Installation and Operation Figure 11: Programming page of the HAC-8R...
-
Page 18: Section 3 - Using The Helix Ats
Helix ATS Installation Manual Section 3 – Using the Helix ATS 3.1 Viewing Parameters on the HAC-8R Home Page Event1 - Event4 These fields show the status of the four Dry Contact inputs. The Home Page is shown in Figure 12. To access the They will appear as the label set for the Event inputs on the Home Page, click "Home"... - Page 19 Configuration and Usage Off - This indicates the input currently has no power more information. available. The background of the field will be gray. Active Energy (W/h) Internal Temperature This column shows the power draw of each output in Indicates the internal temperature of the HAC-8R enclosure. Watts per Hour.
- Page 20 1. Ensure that the new firmware file is available on your computer. The latest firmware file is available from the LifeSafety Power website. 2. Click the "Upgrade" button. The Upgrade window will appear. 3. Click "Browse..." and locate the new firmware file with the file extension ".bin"...
- Page 21 Configuration and Usage Figure 14: The Tools page of the HAC-8R...
-
Page 22: Appendix 1 - Software Agreement
INFORMATION. crets of LIFESAFETY POWER, and Recipient shall not disclose it to any third party Notices. Recipient shall not remove or alter any copyright, trademark except to the extent required by law. Furthermore, Recipient receives no intel- or other proprietary notice that appears on or in the Software. - Page 23 LIFESAFETY POWER for the reasonable cost of the audit, SENTIAL PURPOSE. If applicable law limits the application of the provisions of in addition to such other rights and remedies as LIFESAFETY POWER may have. this Section 5(a), LIFESAFETY POWER’s liability will be limited to the maximum LIFESAFETY POWER will not conduct an audit more than once per year.
- Page 24 LifeSafety Power’s only ob- www.lifesafetypower.com ligations are those in the LifeSafety Power Standard Terms and Conditions of Sale for this product, and in no case will Tel (888) 577-2898 LifeSafety Power or its distributors be liable for any incidental, indirect, or consequential damages arising from the info1@lifesafetypower.com...
Need help?
Do you have a question about the Helix ATS HAC-8R and is the answer not in the manual?
Questions and answers