Subscribe to Our Youtube Channel
Related Manuals for Bandini Industrie GBD TOP 291
Summary of Contents for Bandini Industrie GBD TOP 291
- Page 1 Linear hydraulic operators TOP (291 - 391 - 441) INSTRUCTIONS FOR INSTALLATION...
-
Page 2: Electrical Connections
ELECTRICAL CONNECTIONS 1 Antenna. 2 Electronic equipment container. 3 Screened coaxial cable. 4 Electrolock 5 Key-selector; cable with 3 conductors of 0.5 mm². 6 220-230V operators; power supply, cable with 4 conductors oF 1.5 mm² each: white= motor common, brown= opening phase, black= closing phase. 7 Power supply line to equipment 220-230V 50-60Hz, cable with 3 conductors of min. - Page 3 TOP 291 TOP 391 TOP 441 *(TOP 291/S) *(TOP 391/S) *(TOP 441/S) ALIMENTAZIONE / ALIMENTATION/POWER SUPPLY / ALIMENTACION /ALIMENTAÇÃO / 220/230V-50Hz 220/230V-50Hz 220/230V-50Hz SROMVERSORGUNG / VOEDINGS SPANNING 170 W 190 W POTENZA ASSORBITA / PUISSANCE ABSORBEE / ABDORBED POWER / POTENCIA ABSORBIDA / 190 W POTÊNCIA ABSORVIDA / LEISTUNGSAUFNAHME / OPGENOMEN VERMOGEN *(170W)
-
Page 4: Installation Of The Operators
INSTALLATION OF THE OPERATORS PRELIMINARY WARNINGS Check that the gate structure meets the standards laid down in the regulations in force and that the gate movement is linear and without friction. It is recommended to carry out any operations necessary before installing the operator and in particular to always fit the mechanical end-stops. - Page 6 MOUNTING DIMENSIONS FOR THE SWING TO OPEN COTAS TOP 291 TOP 391 TOP 441 β TOP 291 90° TOP 291 110° TOP 391 90° TOP 391 110° TOP 441 90° 1235 TOP 441 1235 110° If it is not possible to maintain the dimensions A and B indicated in the table, consider the following to calculate the measurements: -for =90°...
- Page 7 OPERATORS TO BE INSTALLED ON BIG PILLARS OR WALLS. MAKE AN ADEQUATE NOTCH IN THE PILLAR OR IN THE WALL ACCORDING TO DIMENSIONS «A» - «B» AS PER THE TABLE ON PAGE 6. WE RECOMMEND TO PUT AN ANTI-CRUSHING PROTECTION CARTER.
- Page 8 ADAPTER KIT ADAPTER KIT AJ00560 : FROM OPERA TOR MODO 290,390,440 TO OPERA TOR TOP 291,391,441 -CUT THE BRACKET AT THE HEIGHT INDICATED IN FIG. 1 -WELD ON THE BRACKET CONTAINED IN THE KIT AS SHOWN IN FIG.2, TAKING CARE TO RESPECT THE DIMENSION “D” AS DESCRIBED ON PAGE 12 OF THE MANUAL.
- Page 9 ELECTROLOCK MOUNTING THE ELECTROLOCK 1 Electrolock 2 electrolock fixing plate 3 Bolt hooker 4 Bolt hooking rabbet 5 Bolt 6 Key cylinder (on request) 7 Gate...
-
Page 10: Force Adjustment
FORCE ADJUSTMENT 1) Valve for adjusting force during opening phase. 2) Valve for adjusting force during closing phase. Use a screwdriver to increase the force by rotating clockwise the opening valve (1) and the closing valve (2) located under the operator. Decrease the force by rotating counterclockwise valves (1) - (2). -
Page 12: Manual Operation
MANUAL OPERATION DEVICE FOR MANUAL OPERATION Turn the cover 1 and lift it, turn the unlocking key 2 anticlockwise by 2 turns and carry out the manual manoeuvre. To reset, turn the key 2 clockwise until it stops without forcing it , and replace the cover into its original position. - Page 13 MANUAL OPERATION DEVICE FOR MANUAL OPERATION Push the cover 3 in the direction of the arrow, inser t the key 4 in the lock 5, turn the key clockwise, turn the unlocking key 2 anticlockwise by 2 turns and carry out the manual manoeuvre. T o reset, turn the key 2 clockwise until it stops without forcing it, turn the key 5 anticlockwise, and replace the cover 3 into its original position.
- Page 14 CE Declaration of conformity The manufacturer: GI.BI.DI. S.r.l. Via Abetone Brennero, 177/B, 46025 Poggio Rusco (MN) ITALY Declares that the products: Linear hydraulic operator: TOP 291, TOP 391, TOP 441 Are in conformity with the following CEE Directives: • LVD Directive 2006/95/CE and subsequent amendments; •...
- Page 16 GI.BI.DI. S.r.l. Via Abetone Brennero, 177/B 46025 Poggio Rusco (MN) - ITALY T el. +39.0386.52.20.11 Fax +39.0386.52.20.31 E-mail: comm@gibidi.com Numero Verde: 800.290156 w w w . g i b i d i . c o m...
Need help?
Do you have a question about the GBD TOP 291 and is the answer not in the manual?
Questions and answers