Advertisement
Quick Links
CS900VD EN (paper)
9/5/05
1:54 PM
Page 1
ENGLISH
Safety Information
For UK Only
BLUE = NEUTRAL / BROWN = LIVE
CONNECT THE MAIN LEAD INTO A MAINS POWER
If the colors of the wires in the mains lead of this
SOCKET
apparatus may not correspond with the colored
markings identifying the terminals in your plug,
POWER SUPPLY 230V. It must not be
proceed as follows:
connected to D.C. mains.
BLUE wire to the terminal coded N (Neutral) or
colored black.
Note: The mains lead of the set is fitted with a molded
BROWN wire to the terminal coded L (Live) or
plug. If the mains socket are not
colored red.
compatible or if for any reason the plug is removed
please follow the directions below. The molded plug
DO NOT make any connection to
cannot be rewired and if removed must be disposed of
the terminal in the plug which is
safely.
marked by the letter E or by the
earth symbol or colored green or
DO NOT under any circumstances plug the
green and yellow.
severed plug into any mains socket as this could result
in electric shock.
A fused plug must be fitted with a 3A
fuse approved by ASTA or BS1362 and
Important: If the plug is removed, rewire the new plug
fuse covers must be always be
as follow:
securely replaced. If you set does not
The wires in the mains plug are colored in
work, the fuse may be blown.
accordance to the following code:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
T H E
L I G H T N I N G
CAUTION: TO REDUCE THE
FLASH AND ARROW-
RISK OF ELECTRIC SHOCK,
HEAD WITHIN THE
D O N O T R E M O V E C O V E R
T R I A N G L E I S
A
( O R B A C K ) . N O U S E R -
W A R N I N G
S I G N
S E RV I C E A B L E PA R T S I N -
ALERTING YOU OF
S I D E . R E F E R S E RV I C I N G
" D A N G E R O U S
T O Q U A L I F I E D S E R V I C E
VOLTAGE" INSIDE
PERSONNEL.
THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING:
TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
The descriptions and characteristics given in this document are given as a general indication and not as a guarantee. In order to provide
the highest quality product possible, we reserve the right to make any improvement or modification without prior notice. The English
version serves as the final reference on all products and operational details should any discrepancies arise in other languages.
Important Information
Safety Precautions
Maintenance
•
Never open the cabinet under any
Disconnect the audio system from the power source
circumstances. Any repairs or internal
before performing any maintenance.
adjustments should be made only by a trained
technician.
Cleaning
•
Never operate this product with the cabinet
Clean the exterior of the system using a soft dust cloth.
removed.
•
Do not use your System immediately after
CD Player
transporting it from a cold place to a warm
CAUTION! This system operates with a laser. It must be
place, as condensation may cause the system to
opened by only a qualified technician.
malfunction.
•
Keep your unit away from humid areas and
Handling CDs
abnormally hot places.
•
Do not touch the signal surfaces. Hold CDs
•
Do not touch the player with wet hands. If
by the edges, or by one edge and the hole.
any liquid enters the player cabinet, take the
•
Do not affix labels or adhesive tapes to the
player to a trained technician for inspection.
label surfaces.
•
This compact disc player uses a laser to read
•
Do not scratch or damage the label. CDs rotate at
the music on the disc. The laser mechanism
high speeds inside the player.
corresponds to the cartridge and stylus of a
•
Do not use damaged (cracked or warped) CDs
GEFAHR EINES
record player. Although this product
ELEKTRISCHEN SCHLAGS
incorporates a laser pick-up lens, it is
Cleaning CDs
completely safe when operated according to
•
Dirty CDs can cause poor sound quality. Always keep
directions.
CDs clean by wiping them gently with a soft cloth
•
Discs rotate at high speed inside the player. Do not
from the inner edge toward the outer perimeter.
use damaged, warped, or cracked discs.
•
If a CD becomes dirty, wet a soft cloth in water,
•
Do not touch the pick-up lens which is located inside
wring it out well, wipe the dirt away gently, and
the disc compartment. To keep dust from collecting
then remove any water drops with a dry cloth.
on the pick-up lens, do not leave the compartment
•
Do not use record cleaning sprays or antistatic
door open for an
agents on CDs. Also, never clean CDs with benzene,
extended period of time. If the lens becomes
thinner, or other volatile solvents which may cause
dirty, clean it with a soft brush, or use an air
damage to disc surface.
blower brush designed for camera lenses.
•
The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
•
Minimum distances around the apparatus for
sufficient ventilation .
•
The ventilation should not be impeded by
covering the ventilation opening with items,
such as newspaper,table-cloths,curtains,etc.
•
No naked flame sources,such as lighted
candles,should be placed on the apparatus.
•
Attention should be drawn to the
environmental aspects of battery disposal .
Getting Started
Using the Remote Control
1. Please open the battery compartment.
2. Insert two batteries (AA, R6, UM- 3 type) making sure the polarity (+/-) matches the marks inside the unit.
3. Replace the cover.
•
Do not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into the fire.
•
Do not mix old and new batteries
and video signal to the TV set from the
Basic Connections
unit.
Use audio cables (Red/ White) and video cable (Yellow)
to connect the DVD player and your TV.
Basic Connection Diagram:
Turn OFF the power and remove the AC cord from the
The diagram below represents a typical connection. In
outlet when connecting the system.
this diagram you can view the
picture from DVD movie discs on your TV set. You can
TV Connection - Normal (Connection Cable
also play the sound from your
included):
stereo VCR through the speakers of this system by
To view the video from DVD discs on your TV set
connecting to AUX 1 or AUX 2 input
connect the Video Out jack of this system to the Video
jacks.
ln jack of your TV set. The video jacks are usually
coloured yellow. Use the included video cable with
Coaxial Digital Output Connection
yellow plugs on each end.
If you want to connect Coaxial Digital Out, connect a
coaxial cable (not provided) from
TV Connection - S- Video (Cable Not included):
COAXIAL IN of the CDR/ W Recorder or AV Amplifier to
If your TV set has an S- Video Input jack, you can
the COAXIAL DIGITAL AUDIO
connect your TV to the S- Video Out jack on the back of
OUTPUT of the DVD Receiver.
this system.
•
CDR/ W Recorder or AV Amplifier with a Dolby
Digital Decoder.
TV Connection- Scart (Scart Cable Not included):
If your TV set has a Scart Input, you can connect your
TV to the Scart Output on the back
of this system. The Scart Cable can transmit both audio
Video input
Audio input
Audio output
Basic Disc Playback
•
Press the ENTER button to have the selected picture
Interactive Function Buttons
displayed on the TV screen.
(DVD)
•
Press the PAUSE/ STEP button to temporarily stop
the Auto- Run mode from occuring. Press the PLAY
1. AUDIO MENU button:
button to resume Auto-Run mode.
To press this button, you can change the audio
•
Press the STOP button to stop the Auto- Run mode.
language from the one selected at the initial
4. Forward or Reverse Skipping
settings to a different language, if available.
Press the SKIP
buttons to scroll through
2. SUBTITLE MENU button:
the pictures.
To press this button, you can change the subtitle
language from the one selected at the initial
settings to a different language, if available.
3. TITLE MENU button:
Return Function (VCD)
Press the TITLE MENU button, then the DVD menu
or titles available on the disc will be displayed on
Press the RETURN button once and the unit will go back
the TV screen. You can use the Navigation buttons
to the main menu when playing version 2.0 VCD discs.
to select programs.
4. ANGLE button:
Some DVD discs may contain scenes which have
been shot simultaneously from a number of
different camera angles. The jacket or case of discs
that are recorded with angle will be marked. Press
the ANGLE button to choose the desired angle, TV
screen will change within one or two seconds.
•
The buttons mentioned in 1- 4 work only when the
disc played supports the corresponding functions.
Picture CD Operations
1. Auto- Run mode
After loading a picture CD into the disc tray, the
player will automatically play the photos in the
picture CD disc one by one during playback mode.
•
If you disc contains folders, use the Navigation
buttons
to select the desired picture
from the folders and press the ENTER button to
start playback.
2. Rotating pictures
During playback mode, press one of the four
Navigation buttons
once to rotate the
picture 90 degrees on TV screen.
3. Choosing pictures from menus
•
Press the STOP button during playback to go into
the disc menu.
•
Press the Navigation buttons
to view pictures
from the menu.
Player Menus
The Preference Setup Menu
Changing Parental Level
You must stop playback to enter preferences mode. The
Select your desired Rating level "1" to "8" to disable the
setting structure is:
playing of specified DVDs which are unsuitable for
children.
1. Press the Navigation buttons
Audio
Parental menu.
Select among the available languages listed.
2. Press the Navigation buttons
select your desired rating level. Press the ENTER
Subtitle
button to go into the Password Verify page. If not
select (Parental) rating level, select "Open" to leave
Select among the available languages listed.
and not input password.
3. Input your present password in the Password Verify
Disc Menu
page. (Factory preset Password: 1234)
Select among the available languages listed.
4. If your password is incorrect, please re- enter your
password again. If your password is correct, press
the ENTER button to confirm your rating level
Parental
selection.
Select among the following rating levels:
5. The old rating level will change to your desired new
1
KID SAF ( Kid Safe)
Rating level.
2
G ( All ages)
3
PG ( Parental Guidance)
Note: The Password code is set by yourself on the
4
PG 13 ( Parental Guidance less than 13 years old)
Password Change page.
5
PGR ( Under 17 years old. Parental Guidance
suggested)
6
R ( Under 17 years old. Parental Guidance strongly
suggested)
7
NC 17 ( 17 years old and above)
8
Adult ( Adult only)
•
Read "Changing Parental Level" for details.
Password
Select this option for password changing.
Safety Information
CAUTION!
Invisible laser radiation when open. Avoid exposure to
beam. Class 1 laser product. This system must be opened
only by qualified technicians to prevent accidents
caused by the laser beam.
LASER λ = 780 nm, P max = 5 mW
Rating Information: At bottom/rear of the unit.
This unit comply with the existing requirements
In accordance with the rating plate of the unit, this unit
complies with
current standards concerning electrical safety and
electromagnetic
compatibility.
Please respect the environment Before throwing any
batteries away, consult your distributor who may be
able to take them back for specific recycling.
Have a Blast- Just Not in Your Eardrums
Make sure you turn down the volume on the unit
before you put on headphones. Increase the volume to
the desired level only after headphone are in place.
THE EXCLAMATION
POINT WITHIN THE
T R I A N G L E I S A
WARNING
SIGN
ALERTING YOU OF
I M P O R T A N T
I N S T R U C T I O N S
A C C O M PA N Y I N G
T H E
P R O D U C T.
Portions based upon Microsoft Windows Media Technologies. Copyright © 1999 Microsoft Corporation. All Rights
Reserved. Microsoft, Windows Media, and the Windows Logo are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Important Information
Important Battery Information
•
Remove the batteries to avoid leakage if you
do not use your remote control for more than one
month.
•
Discard leaky batteries immediately as leaking
electronic equipment, at their end-of-life, should be
batteries may cause skin burns or other personal
disposed of separately from your household waste.
Please, dispose of this equipment at your local
injuries. Dispose of batteries in the proper manner,
community waste collection/recycling centre.
according to provincial and local regulations.
•
Any battery may leak electrolyte under the
In the European Union there are separate collection
following circumstances:
systems for
used electrical and electronic product.
- if mixed with a different battery type,
Please, help us to conserve the environment we live in!.
- if inserted incorrectly,
- if all batteries are not replaced at the same
time,
Note:
The normal function of the product may be disturbed by
- if disposed of in fire, or
Strong Electro Magnetic Interference. If so, simply reset
- if an attempt is made to charge a battery not
intended to be recharged.
the product to resume normal operation by following
the instruction manual. In case the function could not
resume, please use the product in other location.
Headset Safety
•
Do not play your headset at high volume.
Installation
Hearing experts warn against extended high-
To ensure sufficient ventilation, keep the spacings
volume play.
shown below free from other surfaces:
•
If you experience ringing in your ears, reduce
volume or discontinue use.
•
You should use with extreme caution or
temporarily discontinue use in potentially
hazardous situations.
Even if your headset is an open-air designed to let
10 cm
you to hear outside sounds, do not turn up the
volume so high that you are unable to hear what is
around you.
Don't Infringe
This product should only be used for the purposes for
which it is sold, that is, entertainment, violating no
copyright law. Any attempts to use this product for
which it is not intended is unlawful and therefore not
condoned by Thomson.
Side View
Radio Operations
Manual Tuning
light up if the station in FM Stereo mode is
selected. This indicator will turn off if it is in mono
1. Press the FUNCTION button on the front panel
mode.
repeatedly to select the Tuner mode. The word
5. Repeat step 3 to 5 to select another station.
"Radio" will appear on the display.
2. Press the BAND button on the front panel
repeatedly to select the AM or FM tuning mode.
3. Rotate the TUNING knob on the front panel
clockwise or anti- clockwise to tune in a radio
station. You can listen to your desired station when
it is tuned in.
4. In FM tuning mode, press the FM MODE button on
the front panel repeatedly to select the FM mono
or FM stereo mode. The FM Stereo indicator will
Basic Disc Playback
The player memories the point where you
Starting and Stopping
stopped.
If you press the PLAY button again, playback starts
Playback
automatically from the point where you stopped.
1. Press the CD Door downward to open the disc tray
(Resuming Playback)
('Open' appears on the display and TV screen).
If the STOP button is pressed twice, the TV screen
•
Hold the disc without touching either of its
shows "
surfaces, position it with the printed title side
•
Note: Some discs may not start resuming playback.
facing up, align it with the guides, and place it in
its proper position.
2. Close the CD Door. The disc tray closes
('Load' appears on the display and 'LOADING'
appears on TV screen), and play start
automatically.
If a MENU appears on the TV screen:
Press the Navigation buttons
, to select a
desired item, then press the ENTER button. Playback
of the selected item will start.
Note: For more details, please refer to the jacket or
case of the disc. Press the VOLUME
buttons of the front panel or remote handset to select
your desired volume level.
3. Stopping Playback
Press the STOP button once and "Press Play Key To
Continue" appears on the TV screen.
Other Functions
Zoom
Mute
Press the ZOOM button during normal, slow or still
Press the MUTE button once to temporarily mute the
playback mode. This player can magnify (x2, x3, x4) a
sound of the playing disc. Press this button again to
picture and use the Navigation buttons
resume the disc playing sound.
to select desired part of the zoomed pic-
ture.
Preset EQ.
OSD Display
1. 4 preset equalizing effects are available and they
circulates as follow:
During playback you can display various information
ROCK / POP / CLASSIC / FLAT
about elapsed and remaining playing time by pressing
2. Press the PRESET EQ. button on the remote control
the DISPLAY button.
repeatedly to choose your desired equalizing effect.
DVD: Title Elapsed / Title Remain / Chapter Elapsed /
Chapter Remain / Display Off
VCD: Single Elapsed / Single Remain / Display off
E-Bass
MP3: Single Elapsed / Single Remain
1. Press the E-BASS button once to turn on the extra
CD: Single Elapsed / Single Remain / Total Elapsed / Total
bass sound effect. "EBASS ON" will appear on the
Remain / Display off
display.
2. Press the E- BASS button again to turn off the extra
bass sound effect. "EBASS OFF" will appear on the
Audio Mode (Audio CD)
display.
Press the AUDIO MODE button to cycle through the
audio modes. The audio modes vary depending on the
disc played, but include MONO LEFT, MONO RIGHT, MIX
MONO, STEREO, etc. "
" will appear if the disc does
not support audio mode changing.
L R Channel Balance
1. Press the BALANCE button to enter the L R Channel
Balance mode. The Balance Bar
"---- I I---- " will appear on the display.
2. Press the L or R button repeatedly to move the
balance bar index left or right as desired to calibrate
the compared speaker output ratio of front left and
front right speakers.
•
If the bar index lies between 2 ends, the 2 speakers
will output sound in compared ratio with respect to
the position of the bar index. Only when the index is
in the middle will the 2 speakers output equal
sound volume.
Troubleshooting Tips
Before requesting service for this player, check below
No operations can be performed with the remote
for a possible cause of the problem you are
control unit
experiencing. Some simple checks or a adjustment on
•
Check the batteries are installed with the correct
your part may eliminate the problem and restore proper
polarities (+ and -).
operation.
•
The batteries are exhausted: replace them with new
to select
ones.
No power
•
Point the remote control unit at the remote control
and then
to
•
Insert the AC power plug securely into the power
sensor and operate.
outlet.
•
Operate the remote control unit at a distance of not
more than 7 m from the remote control sensor.
Play fails to start even when PLAY is pressed. Play starts
•
Remove the obstacles between the remote control
but then stops immediately
unit and remote control sensor.
•
Condensation has formed: wait about 1 to 2 hours
to allow the player to dry out.
No key operation (by the main unit and/ or the remote
•
This player cannot play a disc other than DVD,
control unit) is effective.
Video CD and CD.
•
Press ON/ STANDBY to set the player to the standby
•
The disc may be dirty and may require cleaning.
mode and then back to ON. Alternatively, press ON/
•
Ensure that the disc is installed with the lable side
STANDBY to set the player to the standby mode,
up.
disconnect the power plug and then re- connect it.
(The player may not be operating properly due to
No picture
lightning, static electricity or some other external
•
Ensure that the equipment is connected properly.
factor.)
•
Ensure that the input setting for the TV is "Video".
Play does not start even when title is selected
No sound, Distorted sound
•
Confirm the RATING LEVEL setting.
•
Ensure that the equipment is connected properly.
•
Ensure that the input setting for the TV and stereo
Audio soundtrack and/ or subtitle language is not the
system are correct.
disc, the initial settings.
•
If the audio soundtrack and/ or subtitle language
Picture is distorted during rapid advance or rapid
does not exist on the language selected at the initial
reverse.
settings will not be seen/ heard.
•
The picture will be somewhat distorted at times: this
is normal.
No rapid advance (or rapid reverse play)
•
Some discs may have sections which prohibit rapid
advance (or rapid reverse.)
No 4: 3 (16: 9) picture.
•
Choose the correct setup "TV SCREEN" item which
matches the TV set used.
ADVARSEL!
USYNLIG LASERSTRÅLNING VED ÅBNING NAR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNGDÅ UDSAETTELSE FOR STRÅLNING.
VORSICHT!
UNSICHTBARE LASERSTRALUNG
WENN ABDECKUNG GEÖFFNET UND SICHERHEITS–
VERRIEGELUNG ÜBERBRÜCKT.
NICHT DEM LASERSTRAHL AUSSETZEN!
CAUTION – INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS FAILED OR
DEFEATED. AVOID EXPOSURE TO BEAM.
ATTENTION – RAYONNEMENT LASER INVISIBLE
DANGEREUX EN CAS D'OUVERTURE ET LORSQUE
LA SECURITE EST NEUTRALISEE.
EXPOSITION DANGEREUSE AU FAISCEAU.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A LASER DE CLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPP ARAT
VARNING–
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD OCH SPÄRRAN ÄR URKOPPLADE.
BETRAKTA EJ STRÅLEN.
VARO!
AVATTAESSA JA SOUJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE.
LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.
THOMSON
46, quai Alphonse Le Gallo
92648 Boulogne
Cedex FRANCE
www.thomson.net
56125330
Getting Started
Your THOMSON product is designed and
manufactured with high quality materials
and components which can be recycled and
reused.
This symbol means that electrical and
Front View
10 cm
10 cm
10 cm
5 cm
Basic Disc Playback
Skip and Searching
1. SKIP
buttons:
Press these buttons to go to the previous/ next
chapter (DVD) or track (VCD/ CD).
2. SLOW/ F, SLOW/ R buttons:
Press these buttons to select slow- motion forward
(SLOW/ F) or rewind (SLOW/ R) playback at 1/ 2, 1/ 4,
1/ 8 and 1/ 16 normal speed without sound.
•
Press the PLAY button to return to normal playback.
3. PAUSE/ STEP button:
Press the PAUSE/ STEP button once to pause the
picture. Repeatedly press the PAUSE/ STEP button
to play the DVD one frame at a time.
•
Press the PLAY button to resume normal playback.
4. REV and FWD buttons:
These buttons allow skipping ahead/ back at 4- level
speeds as 2x, 4x, 8x, and 16x.
•
Press the PLAY button to return to normal playback.
Time Searching
1. SEARCH button
Press this button repeatedly to select desired
playback position by chapter / title / track / time.
". Then the player stops completely.
2. Use the Numeric Keypad (0-9) to input your desired
chapter, title, track or time. Press the CLEAR button
of the remote control to erase the wrong input
digits.
•
The input numbers must be two digits. For example,
if the desired track is 8, then you must press "08".
Player Menus
Speaker Setup
General Setup
Using the player menus
1. Press the SET UP button to display the player's setup
menu.
2. Select a menu icon using the Navigation buttons
. Then select one of the available options
using the Navigation buttons
.
3. Press the Navigation buttons
to access the
submenu and use the Navigation buttons
to select an option. Then press the ENTER
button to confirm your selection.
4. Return to a previous menu using the Nagivation
button
. To exit from the player menus, press the
SET UP button again or select the icon "X" and
press the ENTER button.
Maintenance
No subtitles.
•
Subtitles appear only with discs which contain
them.
•
Subtitles are cleared from the TV monitor, Perforn
the steps on page 8 to display the subtitles.
Alternative audio soundtrack (or subtitle) language fail
to be selected.
•
An alternative language is not selected with discs
which do not contain more than one language.
Maintenance
Disconnect the audio system from the power source
before performing any maintenance.
Cleaning
Clean the exterior of the system using a soft dust cloth.
CD Player
CAUTION! This system operates with a laser. It must be
opened by only a qualified technician.
Handling CDs
•
Do not touch the signal surfaces. Hold CDs
by the edges, or by one edge and the hole.
•
Do not affix labels or adhesive tapes to the
label surfaces.
•
Do not scratch or damage the label. CDs rotate at
high speeds inside the player.
•
Do not use damaged (cracked or warped) CDs
Cleaning CDs
•
Dirty CDs can cause poor sound quality. Always
keep CDs clean by wiping them gently with a soft
cloth from the inner edge toward the outer
perimeter.
•
If a CD becomes dirty, wet a soft cloth in water,
wring it out well, wipe the dirt away gently, and
then remove any water drops with a dry cloth.
EN
It is important to read this instruction book prior to using your new product for the first time.
Getting Started
Display
Back View
1. AM Loop Antenna terminal
2. FM Antenna (attached)
3. SCART output
4. AUX 2 input
1. Dolby Digital indicator
5. AC power cord
2. DVD playback
6. Spearker terminals
3. DTS indicator
7. AUX 1 input
4. SVCD / VCD / CD indicator
8. Audio (DVD) output
5. MP3 playback
9. Composite VIDEO output
10. COAXIAL digital audio output
11. Optical output
12. S-VIDEO output
Remote Control Unit
Front View
1. Standby button
2. Power on/off button
3. Standby indicator
4. Changes functions
5. FM Stereo indicator
6. Stops playback
7. Skips backward
8. Skips forward
9. Headphone jack
10. Starts playback
11. Adjust volume
12. FM mode button
13. Selects radio bands
14. Remote sensor
15. Display
16. Radio tuning knob
17. Disc tray - press on
to open or close the disc tray
Basic Disc Playback
Programming Playback (DVD/
Repeat Playback
CD/ VCD)
The repeat functions that you can enjoy are
dependent on the disc types played.
This unit has a 20 tracks programmable memory that
DVD: Title repeat, chapter repeat and given portion
allows you to program up to 20 tracks on any disc for
repeat.
playback in any desired order. You may program 20
VCD/ CD: All tracks repeat, single track repeat and
different tracks or you may also program certain tracks
given portion repeat.
to play more than once. Programmed playback only
works for DVD's and CD's, it does not work on MP3 CD's.
REPEAT button:
•
You can repeatedly play a title (DVD) or all tracks
To program playback, proceed as follows:
(VCD/ CD) when " Title " or " All " appears on TV
1. While playback is stopped, press the PROGRAM
screen respectively.
button, the Program menu will appear on the TV
•
You can repeatedly play a chapter (DVD) or a
screen.
single tracks (SVCD / VCD / CD) when
2. Press the Numeric Keypad (0-9) to input chapter /
"Chapter " or " Track " appears on TV screen
track numbers for each program position. The
respectively.
cursor will automatically jump to the next program
•
You can cancel repeat functions when "Off "
position for inputting another numbers.
appears on TV screen.
3. Repeat step 2 until all desired chapters or tracks
have been programmed (up to 20). You can repeat a
REPEAT A- B button:
chapter or track more than once if desired.
You can repeatedly play a given portion by operating
4. Use the Navigation buttons
to select
as following:
"Start".
1. Press this button once to define the portion head.
5. Press the ENTER button to begin programmed
2. Press this button again to define the portion toe.
playback.
And then the portion will be played repeatedly.
•
Press this button again to return to normal
Cancelling Programs
playback.
To cancel the Program function, press the PROGRAM
button again. Use the Navigation buttons
to select "Stop" and then press the ENTER button.
Player Menus
Video Out
Dolby Digial
Select the colour video type and switch to the mode
Preferences
Setup
to fit your connector type:
•
Scart/ CVBS: Select when using CVBS composite
Video Output (if S- Video connector is provided.)
•
Scart/ RGB: Select when using RGB Video signal
Exit Setup
and TV to AV automatic switching mode control
signal.
Angle Mark
This only works when there is the angle feature on a
DVD disc.
•
Select "ON" to show the angle mark on the TV
screen when playing a DVD.
•
Select "OFF" the angle mark is not shown.
The General Setup Menu
OSD Lang
TV Display
Select among the available languages listed for OSD
•
Normal / PS: "PS" stands for "Pan Scan" Select this
display.
option when the unit is connected with a normal TV.
Wide- Screen images are shown on the screen, but
Screen Saver
with some parts cut automatically.
Select between "ON" and "OFF" to turn screen saver
•
Normal / LB: "LB" stands for "Letter Box" Select
on or off. The screen saver image appears when the
this option when the unit is connected with a
unit stops or the image is motionless for
normal TV. Wide- screen images are shown on the
approximately 1 minute. This saver can keep the
screen, with black belt on the top and bottom.
screen from being damaged.
•
Wide: Select this option when the unit is connected
with a wide - screen TV.
Audio In
TV Type
Select among the audio in sources available.
You may select according to the colour system of the TV
to be connected.
•
Select "NTSC" for a NTSC TV.
•
Select "PAL" for a PAL TV.
More Information
Angle cannot be changed.
DivX files
•
This function is dependent on software availability.
DivX is the name of a revolutionary new video codec
Even if a disc has a number of angles recorded,
which is based on the new MPEG-4 compression
these angles may be recorded for specific scenes
standard for video. Whether DivX files play correctly
only.
on your player or not depends on the preparation
and production of the audio and video files, the
The password for rating level has been forgotten.
codecs and the type of recording equipment used, as
•
Please contact your local sales dealer.
well as on your computer's parameters. It is therefore
possible that you cannot play a DivX file or that part
No menu play on VCD.
or all of it is defective. It also sometimes happens that
•
This function works only for Video CDs with
you can play the images (video) but not the sound
playback control.
(audio).
DivX disc compatibility with this player is limited as
follows:
•
The maximum resolution of the DivX file is below
720x576 (W x H) pixels.
•
Do not use record cleaning sprays or antistatic
•
DivX filenames should not exceed 56 characters.
agents on CDs. Also, never clean CDs with benzene,
•
If the video and audio structure of the recorded
thinner, or other volatile solvents which may cause
file is not interleaved, either video or audio is
damage to disc surface.
outputted.
•
If the file is recorded with GMC, the unit supports
CD Lens Care
only 1-point GMC. GMC is the acronym for Global
When your CD lens gets dirty it can also cause the
Motion Compensation. It is an encoding tool
system to output poor sound quality. To clean the lens
specified in the MPEG4 standard. Some MPEG4
you will need to purchase a CD lens cleaner which can
encoders, like DivX or XviD, have this
maintain the output sound quality of your system. For
option.There are different levels of GMC
instructions on cleaning the CD lens, refer to the ones
encoding, usually called 1-point, 2-point, or 3-
accompanying the lens cleaner.
point GMC.
•
DivX files with subtitles in .SRT, .SUB and .SMI
formats can be played. Correct playback of all
languages may not be possible as some
characters may be missing.
u s e r
m a n u a l
CS900VD
6. Title indicator
11. Time / messages
7. Chapter indicator
12. Playback indicator
8. AM / FM band
13. Program
9. Station tuned indicator
14. Angle
10. Frequency
15. Repeat 1 / All
1. Selects display options
29. Searches forward
2. Selects zoom options
30. Searches backward
3. Selects repeat modes
31. Accesses search menu
4. Selects angle options
32. Repeats selected potion on
5. Starts slow foward
a disc
6. Starts slow reverse
33. Turns unit on/off
7. Pause / Step
34. Accesses program mode
8. Starts Playback
9. Skips backward
10. Navigation buttons
11. Returns to disc menu (VCD)
12. Numeric Keypad (0-9)
13. Accesses Title / Menu
14. Accesses DVD Menu
15. Adjusts E- BASS
16. Accesses L R Channel
Balance setting
17. Adjust L R channel balance
18. Mutes sound
19. Adjust volume
20. Selects Preset EQ.
21. Accesses Audio Menu
22. Accesses Subtitle Menu
23. Accesses Audio Mode
24. Clears inputs
25. Accesses setup menu
26. Confirms selections
27. Skips forward
28. Stops playback
MP3 Disc Operations
1. Press the CD Door downward once to open the
disc tray.
2. Insert an MP3 disc with the label side facing up on
the disc tray.
3. Press the CD Door downward again to close the
disc tray.
4. After loading, the Root/ Folder Menu of the MP3
disc will appear on the TV screen.
5. Press the Navigation buttons
to select
your desired file and press the ENTER button to
confirm.The player will play your selected track.
6. All the music tracks of the disc will be able to
display by pressing the Navigation buttons
repeatedly. Press the DISPLAY button
to display the remain playtime and elapsed
playtime alternately.
7. Press the REPEAT button repeatedly and "Repeat
One" or "Repeat Folder" will appear on the TV
screen and you can repeat playing 1 track or the
whole folder continuously.
The Speaker Setup Menu
Downmix
LT/ RT: The front speakers are in theatrical LT/ RT
downmix mode.
Stereo: The front speakers are in Stereo Downmix
mode.
The Dolby Digital Setup Menu
Dynamic
The compression mode is selected to adjust linear
compression rate to obtain the different compression
results of the signals.
Technical Data
Power Requirements: AC 230V ~ 50Hz
Power Consumption: 50W
Signal System: NTSC / PAL
Weight: 2.8 Kg (main unit)
Dimensions: 155 (L) x 228 (W) x 202.5 (H) mm
Operating Temperature Range: +5 to +35° C
Operating Humidity Range: 5 to 90% (no
condensation)
Discs Played:
(1) DVD- VIDEO Disc: 12 cm single- sided, single- layer
/ 12 cm single- sided, dual- layer
12 cm double- sided, single- layer / 8 cm single- sided,
single- layer
8 cm single- sided, dual- layer / 8 cm double- sided,
single- layer
(2) Compact Disc: 12 cm disc / 8 cm disc
Specifications are subject to change without notice.
Weight and dimensions are approximate.
This product incorporates copyright protection
technology that is protected by method claims of
certain U. S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Apparatus Claims of U. S. Patent Nos. 4,631,603;
4,577,216; 4,819,098; 4,907,093 and 6,516,132
licensed for limited viewing uses only.
The Region number for this DVD player is:
Advertisement
