Related Manuals for FLEETFLIX LITE PRO+
Summary of Contents for FLEETFLIX LITE PRO+
- Page 1 SEE WHAT’S AHEAD Fleetflix lite pro+ DUAL DASH CAMERA INSTALL GUIDE 678.759.2544 sales@fleethoster.com www.fleethoster.com...
- Page 2 Preface This installation guide for FleetFlix Lite Pro+ is designed to assist installers in the proper and e7icient installation of FleetFlix Lite Pro+ and its associated accessories. The goal is to streamline the installation process and enhance overall e7iciency. The guide is structured into several sections including a preface, system overview, preparation for installation, installation procedures, and acceptance testing and cleanup.
- Page 3 7. In case of any problem in the installation for special vehicles, please contact your reseller. System Overview FleetFlix Lite Pro+ is an AI-enabled dashcam designed to enhance driver safety and streamline fleet management. Utilizing advanced AI technology, it actively identifies risky driving incidents and unsafe behaviors, providing real-time alerts to drivers to mitigate risks.
- Page 4 Schematic Diagram of System Connection-Power Supply through OBD FF Lite Pro+ 678.759.2544 sales@fleethoster.com www.fleethoster.com...
- Page 5 Schematic Diagram of System Connection-Power Supply through Standard Power Cable FF Lite Pro+ Preparation for Installation Relevant personnel must have a comprehensive understanding of the product's functions, applications, and overall components. They should possess knowledge of electrical circuits and vehicle structures, as well as common installation techniques for in-vehicle devices. Prior to device installation, relevant personnel should be familiar with the specific vehicle model, the optimal installation locations for the dashcam and auxiliary cameras, the types and lengths of cables required for each vehicle model, and the list of supplementary materials needed.
- Page 6 Connecting Necessary Signal Cables for Lane Departure Warning: Ensure the following signal cables are connected for FleetFlix Lite Pro+ intelligent assisted driving functions: CAN Data Cable: Provides accurate vehicle speed (Note: GPS speed may negate the need for this connection).
- Page 7 Left and Right Steering Signal Cables: Obtain steering information. For locating these cables: Consult the vehicle maintenance engineer for the specific position of the CAN data cable. Typically, the left and right steering signal cables are found on the fuse board beneath the steering wheel or passenger dashboard.
- Page 8 Installation of SIM Card and Memory Card Take out the Dashcam (power-o7), and use the Allen key in the kit to open the card slot panel on the right of the Dashcam by turning counterclockwise. Install SIM card and Micro SD card as shown in the figure below (pay attention to the insertion direction of the cards).
- Page 9 Micro SD card, which can be used in a wide operating temperature range (-40℃ to 85℃) and has strong stability. FleetFlix recommended Micro SD cards are preferred. Failure to use the appropriate card as required may damage the accessories or even the device.
- Page 10 device in the middle as required (The deviation of the Dashcam relative to the centerline of the front windshield shall be calculated with the centerline of the forward-facing lens). (2) When conditions permit, the height of the DSC lens shall not exceed the height of the driver's eyes, and the installation position shall be as low as possible provided that the driver's view is not obstructed.
- Page 11 Installation of Dashcam Bracket Park the vehicle on the horizontal ground, clean the interior and exterior of the glass in the target installation area with alcohol cotton to ensure that no dirt on the glass in this area will a7ect the angle of view of the lens for road condition monitoring, and ensure the glass is dry.
- Page 12 Installation of Dashcam Connect the Dashcam to the bracket with the front side facing inward (with the teeth on the right side of the bracket engaged with those on the right inner side of the Dashcam), and tighten the bracket stud clockwise with a PH2 cross screwdriver (before tightening, first adjust the Dashcam to be vertical).
- Page 13 Angle Adjustment and Fixation of Dashcam Adjust the Dashcam back and forth so that it is vertical. Fasten the bracket stud to ensure that the angle of the Dashcam will not be changed easily, and fix the Dashcam. When fixing, ensure that the cockpit camera screen meets the following conditions: 1) The center of the cockpit shall be in the middle of the screen.
- Page 14 If the device is fixed and installed after power-on, it shall be powered on again before being tested or used. The GPS module built in FleetFlix Lite Pro+ is an inertial navigation module, and the above requirements can ensure the normal operation of inertial navigation products.
- Page 15 If the mode of power supply connection through the loose wire is adopted, according to the definition of power loose wire, connect POWER/ACC/GND with the power cable of the vehicle, respectively. *Note: The power line shall be connected using "special stripping-free connection terminal" where possible (no stripping is required, so as to avoid the risk of electric leakage), and the connection shall be wrapped with insulated rubber tape to avoid electric leakage/short circuit.
- Page 16 Left steering/right steering/reversing signal After locating the fuse board below the steering wheel or the front passenger dashboard, measure the cable corresponding to left steering/right steering/reversing signal according to the tips on the cover back of the fuse board or using a multimeter.
- Page 17 Since FleetFlix Lite Pro+ has a power supply box with a built-in turning-on/o7 control strategy, it is necessary to fix the power supply box at a certain position on the vehicle. Attention should be paid to the following items when the fixing position is selected:...
- Page 18 Fixing position 1 of the power supply box: Remove the side ba7le of the driving seat, tear o7 the 3M tape on the power supply box, and fix it to the left or right ba7le, as shown below: Fixing position 2 of the power supply box: Fix the power supply box on the right ba7le of the driving seat with exposed cabling.
- Page 19 Measure the vertical height (accurate to cm/inch) from the ground to the lens for road condition monitoring of FleetFlix Lite Pro+ with a tower ruler or tape and take it as the ADAS lens installation height. Measure the horizontal distance from the lens for road condition monitoring of FleetFlix Lite Pro+ to the outermost edge of the left tire (standing outside the vehicle and facing the left side of the front end) and take it as the left margin of the ADAS lens.