Related Manuals for FLEETFLIX LITE
Summary of Contents for FLEETFLIX LITE
- Page 1 SEE WHAT’S AHEAD Fleetflix lite DASH CAMERA INSTALL GUIDE 678.759.2544 sales@fleethoster.com www.fleethoster.com...
- Page 2 Preface This installation guide for FleetFlix Lite is designed to assist installers in the proper and e5icient installation of FleetFlix Lite and its associated accessories. The goal is to streamline the installation process and enhance overall e5iciency. The guide is structured into several sections including a preface, system overview, preparation for installation, installation procedures, and acceptance testing and cleanup.
- Page 3 7. In case of any problem in the installation for special vehicles, please contact your reseller. System Overview FleetFlix Lite is a dashcam designed to enhance driver safety and streamline fleet management operations. It provides real-time and precise vehicle position information along with operational data to the fleet management platform.
- Page 4 Schematic Diagram of System Connection-Power Supply through OBD Schematic Diagram of System Connection-Power Supply through Standard Power Cable Preparation for Installation Relevant personnel must have a comprehensive understanding of the product's functions, applications, and overall components. They should possess knowledge of electrical circuits and vehicle structures, as well as common installation techniques for in-vehicle devices.
- Page 5 These options cater to varying installation needs, providing flexibility for both straightforward and more complex installation scenarios. To determine the appropriate power supply connections for FleetFlix Lite: Identifying Constant Power Supply: When the vehicle is turned o5, use a test pencil to check if the circuit is live.
- Page 6 ACC power supply cables typically read about 24V or 12V when the vehicle is in ACC or ignition mode. Important Note: Always begin power supply connections by measuring voltage at the positive and negative terminals with a multimeter to avoid incorrect connections. Preparation for Installation Material and Tool List Installation of SIM Card and Memory Card Take out the Dashcam (power-o5), and use the Allen key in the kit to open the card slot panel on...
- Page 7 Install SIM card and Micro SD card as shown in the figure below (pay attention to the insertion direction of the cards). If you feel smooth and flexible during installation, and hear a clear sound of "Da" when pushing in the cards completely, it indicates that the cards are installed in the correct direction;...
- Page 8 Micro SD card, which can be used in a wide operating temperature range (-40℃ to 85℃) and has strong stability. FleetFlix recommended Micro SD cards are preferred. Failure to use the appropriate card as required may damage the accessories or even the device.
- Page 9 (3) The lens for road condition monitoring of the Dashcam must be within the working range of the left and right wipers (to ensure that the screen of the lens for road condition monitoring is clean and free from stains). (4) The preferred vertical distance from the lens for road condition monitoring of the Dashcam to the ground is in the range of 52 in -95 in(130 cm-240 cm).
- Page 10 Installation of Dashcam Bracket Park the vehicle on the horizontal ground, clean the interior and exterior of the glass in the target installation area with alcohol cotton to ensure that no dirt on the glass in this area will a5ect the angle of view of the lens for road condition monitoring, and ensure the glass is dry.
- Page 11 Installation of Dashcam Connect the Dashcam to the bracket with the front side facing inward (with the teeth on the right side of the bracket engaged with those on the right inner side of the Dashcam), and tighten the bracket stud clockwise with a PH2 cross screwdriver (before tightening, first adjust the Dashcam to be vertical).
- Page 12 Angle Adjustment and Fixation of Dashcam Adjust the Dashcam back and forth so that it is vertical. Fasten the bracket stud to ensure that the angle of the Dashcam will not be changed easily, and fix the Dashcam. When fixing, ensure that the cockpit camera screen meets the following conditions: 1) The center of the cockpit shall be in the middle of the screen.
- Page 13 If the device is fixed and installed after power-on, it shall be powered on again before being tested or used. The GPS module built in FleetFlix Lite is an inertial navigation module, and the above requirements can ensure the normal operation of inertial navigation products.
- Page 14 If the mode of power supply connection through the loose wire is adopted, according to the definition of power loose wire, connect POWER/ACC/GND with the power cable of the vehicle, respectively. *Note: The power line shall be connected using "special stripping-free connection terminal" where possible (no stripping is required, so as to avoid the risk of electric leakage), and the connection shall be wrapped with insulated rubber tape to avoid electric leakage/short circuit.
- Page 15 Cabling Upon the completion of connection of main cables according to the schematic diagram of system connection, as well as power supply connection and connection of signal cables, arrange these cables using a crowbar according to the diagram below and conceal them in the interior trim panel or the panel of the dashboard (i.e.
- Page 16 (1) If the mode of power supply connection through the OBD port or loose wire is adopted, the cabling mode is as follows: Since FleetFlix Lite has a power supply box with a built-in turning-on/o5 control strategy, it is necessary to fix the power supply box at a certain position on the vehicle. Attention should be paid to the following items when the fixing position is selected:...
- Page 17 Fixing position 2 of the power supply box: Fix the power supply box on the right ba5le of the driving seat with exposed cabling. Since the left ba5le may interfere with the door, it is not recommended to install it on the left ba5le with exposed cabling.