Advertisement
Product Name | Upholstery Cleaning Machine |
Model | S1 |
Rated Voltage | 120V 60Hz |
Rated Power | 1200W |
Vacuum Power | 14 KPa |
Water Tank Capacity | Clean: 61OZ (1800ml) Dirty: 32OZ (950ml) |
Ambient Operating Temp | 32°F-122°F |
Waterproof Level | IPX4 |
Product Size | 12.6 x 8.9 x 18.9 Inches |
Net Weight | 9.3 Lbs |
![]() |
Power On/Off
Press the power switch to start the upholstery cleaner. Press again to turn off the upholstery cleaner.
Note: If there is no operation after 30 minutes when powered on, the machine will automatically shut down.
Vacuum Degree
The upholstery cleaner will default to "Standard" mode. Press the button to adjust between
"Turbo" and
"Standard" modes.
Water Temp
The upholstery cleaner will default to "Warm" mode (104°F). Press the
"Temp" button to adjust between
"Warm (104°F)" and
"Hot" (140°F) modes.
When the dirty water tank is full, all of the lights will flash and the buzzer will beep for three consecutive times before entering the standby mode.
Attention: Stop running that upholstery cleaner and unplug it before maintenance or cleaning.
Surface dirt and smudges can be wiped with a damp cloth.
Stubborn dirt can be wiped with a damp cloth with detergent and then cleaned with a dry cloth dipped in water.
Remove all dirty parts from the body, rinse thoroughly with water, and air dry.
Install the self-cleaning brush head on the handle, then turn on the upholstery cleaner. At the same time, press and hold the water button until the pipe is clean
The filter screen in the clean water tank is used to filter impurities in water and scale generated after boiling water, so please clean the filter screen after using it several times to maintain its filtering effect.
The hose of this upholstery cleaner is detachable. If the hose breaks, please remove it and replace it with a new one.
Status | Possible Causes | Solution |
The upholstery cleaner does not work after the switch is turned on. | The plug is not properly connected or is loose, resulting in poor contact. | Turn off the power and plug it in firmly. |
The upholstery cleaner overheats and the protective mode activates. | Refer to the instructions for the protective mode. | |
The internal line or power cord is broken. | Contact Airthereal for support. | |
The product does not spray water. | Nozzle blockage. | Remove the nozzle blockage with a fine needle. |
Low water in the clean water tank. | Add water to the clean water tank to resume operation. | |
The internal water pipe is blocked or broken. | Contact Airthereal for support. | |
Abnormal noise | The suction port of the product is blocked or large waste has been sucked up. | Clear any blockages. |
Motor failure | Contact Airthereal for support. | |
Weak suction or no water absorption. | Too much dirty water in the dirty water tank. | Empty the dirty water tank. |
Hose in broken. | Replace the hose with a new one. | |
Dirt blocking the suction. | Clear any blockages. | |
Abnormal or inoperative. | The ambient temperature is too high or too low. | Keep the upholstery cleaner at a suitable ambient temperature. (32°F - 122°F) |
Contact Airthereal for support. | ||
Hot water is not hot | Slow heating of boiler | Contact Airthereal for support. |
The boiler is not heated. | Contact Airthereal for support. |
IMPORTANT SAFEGUARDS: To avoid the risk of serious injury when using your upholstery cleaner, basic safety precautions must be followed, including but not limited to the following.
Always here to help you www.airthereal.com
Produced for:
West Ryder Technology LLC
2330 Paseo Del Prado STE C304
Las Vegas, NV 89102
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the S1 and is the answer not in the manual?
Questions and answers