Download
Share
Print this page
MD TYPHON Build Instructions
  1. Manuals
  2. Brands
  3. MD Manuals
  4. Toy
  5. TYPHON
  6. Build instructions

MD TYPHON Build Instructions

Hide thumbs

Advertisement

Quick Links

Download this manual
Build Instruc ons
1
C Copyright by eMDe Model Development 2024

Advertisement

loading
Need help?

Need help?

Do you have a question about the TYPHON and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MD TYPHON

Summary of Contents for MD TYPHON

  • Page 1 Build Instruc ons C Copyright by eMDe Model Development 2024...
  • Page 2 Prin ng Minimum printer size: 150mm x 150mm x 175mm 0.4mm Nozzle 0.2mm layer hight The slicer MUST have a Surface Mode. The only slicers with Surface Mode are Ul maker Cura and Raise3D ideaMaker and their deriva ves. Both are free. bule parts must be sliced in Surface Mode and all...
  • Page 3 Part prepara on Remove print incorrec ons and the surfaces marked yellow. They help the prints stay together during prin ng. You can use scissors or run a sharp blade mul ple mes to cut the parts. C Copyright by eMDe Model Development 2024...
  • Page 4 Build Black pins are used for hinges. pins are for alignment only. They can be cut from 1mm carbon They can be cut from 1mm carbon ûber rod, ûber rod, alterna vely from 1mm steel rod. alterna vely printed from PLA in Normal Mode. 8 are needet.
  • Page 5 Build Carbon ûber rod 1mm x 158mm Micro screw M1.2 recommendet Drill the hole in all Pushrodends large enough so that it can rotate free around the screw. Make sure that the elevator controller moves with the pushrod. C Copyright by eMDe Model Development 2024...
  • Page 6 Build 12mm 9 gramm-size servo or smaller. 22mm Min. 220mm cable lenth. C Copyright by eMDe Model Development 2024...
  • Page 7 Build You can choose between two styles of ver cal stabelizer. C Copyright by eMDe Model Development 2024...
  • Page 8 Build 2 x Carbon ûber rods 1mm x 795mm Secure the carbon rods with thin glue. Make sure that they are right in the middle. C Copyright by eMDe Model Development 2024...
  • Page 9 Build C Copyright by eMDe Model Development 2024...
  • Page 10 Build 12mm Cut the front tab of the 9 gramm-size servo or smaller. servo away to make it ût. 22mm Min. 170mm cable lenth. Wing servo neutral posi on should be at 15° to get mechanical diûeren al ailerons. Use thick glue to mount the wing servos. C Copyright by eMDe Model Development 2024...
  • Page 11 Build C Copyright by eMDe Model Development 2024...
  • Page 12 Build C Copyright by eMDe Model Development 2024...
  • Page 13 Build Carbon ûber rod 1mm x 43mm Mirror these steps to the other side. Pour thin CA glue into the holes to connect the carbon ûber rod to the print. Do this on both sides. C Copyright by eMDe Model Development 2024...
  • Page 14 Build Brushless motor. Anything from 1404 to 2207 stator size is possible. 2205 2200kv recommendet. Use the motor glueing tool to ûnd the right placement of the motor mount for any motor height. C Copyright by eMDe Model Development 2024...
  • Page 15 Build Secure the motor mount in place with three drops of thick glue Now unscrew the motor and reinforce the motor mount with thin glue. C Copyright by eMDe Model Development 2024...
  • Page 16 Build ESC that ûts the selected motor. Cables should be 270mm long with no ba ery plug. Connect the motor to the ESC. Check motor direc on at this point, you can not get to the ESCs a er the motor pods are glued down. Counter rota ng props recommendet.
  • Page 17 Build 4-5 CH reciever Solder the ba ery plug to the ESC cables in a Y coûgura on. Velcro to secure the ba ery C Copyright by eMDe Model Development 2024...
  • Page 18 Build FPV camera Op onal FPV camera mount. C Copyright by eMDe Model Development 2024...
  • Page 19 Build 5" props Op onal spinners. C Copyright by eMDe Model Development 2024...
  • Page 20 Build C Copyright by eMDe Model Development 2024...
  • Page 21 Build Recommendet setup: Elevator throws: 12mm up / 12mm down Aileron throws: 18mm up / 12mm down Yaw: diûeren al thrust 0%-25%-50% (on 3 posi on switch) Ba ery: anything from 2S 350mah - 4S 2200mah (depending on motor selec on) Maximum ba ery size: 40x30x130mm The ideal CG is 35mm behind the leding edge.
  • Page 22 Build Disclaimer The purchase contains digital ûles that allow you to produce the parts for this airplane on your own 3D printer. No physical product is beeing shipped. The ûles are for personal use only. Please contact me if you want to use them in any commercial way. The ûles may never be passed on to any third party.