HobbyBoss A-6E TRAM Intruder Assembly Instructions Manual

81710
1:48 Scale
Item No.:&1110
PLEASE READ BEFORE OPERATION!
*
Tools recommended as below: (Not included)
Adhesives; Paints; Side Cutters; Sharp Edged Pliers; Modeling Knife; Modeling
File; Nippers; Drill; Scissors; Sand Paper; Soft Cloth; Cyanoacrylate Glue.
*
Make sure to read this instruction listed below before assembling.
*
The kit contains the small parts, they can be dangerous if swallowed by mistake,
so keep them away from reach of children .
*
Cut the all parts off carefully and remove the waste parts into the garbage can.
*
More caution and care should be needed for cutting and handling the photo
etched parts.
*
Make attention that some parts should be attached the decal when assembled.
*
During assembling, please tear up and throw away the plastic bags, or may cause
the dangerous if wearing over head by children's mistake.
*
When using the adhesives and paints, please do not use them in the closed room
or near the fire, also must be very careful to protect your eyes.face and clothes.
*
Adult supervised when assembled by children under 14 years old.
n
m
~
cyanoacrylate glue weight
make hole
~M,jJJBi:
~~ iML
*~TruiwfHIII fm~ :
* :ftfHtm ir..i•mIJ:l.
Ciw
~
*)
=
~m•m•*· ~m•m~•.
* □ Sn,
*@m,
n~ .
ttn,
mrm, ~ .
sn,
$.X1il. ~J;t1. 1 ; .~fsJ• 11<:-=i=-a~.
*
m* □
snB.tn
~ /J,,t,-t:.JJ"FPirfl~••1H11~t11~•1*,
:;r-~m~/J,•1*·
*
i:.JJl!x~i,1j~J!tfiiZ!f.f~lji3:~llJ':jJ.tf1JitI;lt1 J1jj-¥:lli.
* m,imiin,J,,t,tt-¥foJrfl•1*: ~ rnair..iii~~ □ .
*mmmir..im~•-=i=-•*~~~~~•#~•~•.
m~tt
m. ~m1mti~~i3[ilJf;1J•1*ii~1±.
*
i:t~:lit~•1Hiim~tt*~lltl5'.l±D-Ji!i!i..bl<Ji!Mf.l;.
*
lJi1J1t llt EiZ:iifiRi M) L#~~fil*~7.iUl1 l&~, ii
llJ' : i
,H~Jjc~
1m~ ,~~9~.
m
6
~
cut / remov option no cement
tJJ~i
m~
~~/Bi:71<
The method to apply the decals
1.Cut off the decal from the decal paper and put it into
the warm water 40
t:
for 10 seconds.
2.Take the decal from the water and put it on a piece
of clean cloth.
3.Remove the decal slowly from the paper to the
targeted location by a wet finger.
4.Use a piece of dry and soft cloth to press it gently on
the decal until it getting dry and no bubble existing.
7.1<
!iJi!i;f:H1{]
ff ffl JJ
5! :
- . :J=e!ffi~ir-J~n:ttJ.).* Ji!Mf.1;...t.S"F, 1.&1'40" C 1-c~ir-J
iilll.7.1<
9l
;~lOfJ;.
=-
~J§~~~n:tt1.&tE-=i=-iftir-J:(jj...t.
.::=: . *...t~n:tttM&, -¥tliiB*~~n:tt~i,1mili ir-J1 .u:ii.
ll9 .
Jfl$_x,=-:(jj$£J.Hn:tt]l.3~ )J<,=-,
9:i§iili~.
C
r;
~
decal bend repa'r
9lMf;I;
~!lti :11i~I'