SUMMARY Introduction Safety instructions Conditions of use Presentation and features Dimensions Description Installation instructions Installation method using truss hooks DMX512 connection Control Panel Ghibli control panel menu - Option details Master/Slave Mode settings DMX Chart Error Messages Care and maintenance Technical Specifications Warranty USER MANUAL...
All the information found in this manual Be careful to power off your GHIBLI by removing the power plug from the is subject to change without notice. AYRTON reserves the right to modify source, before connecting or disconnecting the luminaire.
Objects made of hard materials such as steel or glass that fall on the unit may cause breakage of the plastic parts or the body. AYRTON cannot be held responsible for the luminaire’s broken plastic parts or body, which are not covered under warranty.
DESCRIPTION INSTALLATION INSTRUCTIONS During installation please observe the instructions according to GB7000.15 / EN60598-2-17 standards and other national standards applicable. This luminaire should be installed by a qualified technician. The fixture should be used in an environment with a temperature between -5°C and +45°C.
INSTALLATION METHOD USING TRUSS HOOKS Refer to the following diagram when installing the GHIBLI with truss hooks using omega bracket: Address 117 Address 59 Address 1 DMX512 CONNECTION WITH TERMINATION PLUG For installations where the DMX cable must extend over long distances, or if it is located near areas with major electrical disturbance, it is recommended to use a DMX termination plug.
DMX controller. Table 1: GHIBLI MENU FUNCTIONS AND OPTIONS The start address must conform to the one set on the DMX controller to Address Address DMX address:001-XXX: DMX address setting control the luminaire. This address is the DMX value that appears on the User Mode Stand Mode User’s mode to change...
GHIBLI CONTROL PANEL MENU – OPTION DETAILS w Long click to exit the menu –“Status” then back to main menu by long click again. The following section provides details on the options that can be selected Pan Reverse through the control panel menu. Refer to the table above. Reverses the PAN movement.
Page 11
RDM PID w Long click the jog wheel to exit menu –“Status” then back to main menu by long click again. Allows you to set the fixture’s RDM PID code. w Double click jog wheel to access main menu. Pan/Tilt Spd w Turn the jog wheel clockwise then display “Options”.
Page 12
Flip Display w Turn the jog wheel clockwise then display“Options”. Allows you to rotate the display by 180°. This can be highly useful when w Double click to access “Options” turn the jog wheel to select the fixture is installed with the head facing down. “Temperature C/ F”.
Page 13
Auto Program then back to main menu by double click again. Allows you to run an internal program (a sequence of scenes) by selecting whether the fixture is operating alone or as a master. Timer PIN w Double click jog wheel to access main menu. The “Timer PIN”...
MASTER/SLAVE MODE SETTINGS TEST HOME Allows you to reset the functions. You can select these functions by A MASTER fixture can send up to 3 different sets of data to a SLAVE adjusting the channel. fixture (e.g., a MASTER fixture can control 3 different SLAVE fixtures which w Double click jog wheel to access main menu.
amount: 250 scenes) THE following chart shows the functions and corresponding values for Press ENTER to confirm. each DMX channel according to mode whether Standard (St), Basic (Ba) Press MODE/ESC to return to the main menu. or Extended (Ex): Example: DMX channel´s functions and their values (58DMX channels): ”Program 2”...
Page 16
DMX channel´s functions and their values (58DMX channels): DMX channel´s functions and their values (58DMX channels): Mode/Channel Value Function Mode/Channel Value Function Zoom Fine: Rotating gobos, cont. rotation 1: 0-255 Zoom adjustment Fine Open Focus : 10-19 Rot. gobo 1 0-255 Continuous adjustment from near to far 20-29...
DMX channel´s functions and their values (58DMX channels): Mode/Channel Value Function DMX channel´s functions and their values (58DMX channels): Mode/Channel Value Function Control, Reset : Not used Iris Fine: 10-14 Display Off 0-255 15-19 Iris Fine Display On Prism 20-24 Display invert Off 0-127 Open...
UPDATING THE LUMINAIRE DIMMER, STROBE • Electronic dimmer for light adjustment from 0 to 100% without color Ayrton is continually upgrading this product line. It is therefore possible change (16-bit) that a new software version is available that will increase the unit’s •...
• Maximum authorized ambient temperature (Ta Max): 45°C • Minimum authorized ambient temperature (Ta Min): -5°C Any modification to the fixture will void the warranty. AYRTON cannot under • Minimum projection distance: 5 m any circumstances be held liable for quality and conformity regarding the installation of this product, which is the responsibility of the installer.
Need help?
Do you have a question about the Ghibli 11450 and is the answer not in the manual?
Questions and answers