Related Manuals for GearLite ADR-9039
Summary of Contents for GearLite ADR-9039
- Page 1 Ross Video Limited ADR-9039 Analog Composite to SDI Reference Converter User Manual Ross Part Number: 9039DR-004 Issue: 04B...
- Page 2 ADR-9039 • Analog Composite to SDI Reference Converter User Manual • Ross Part Number: 9039DR-004 • Document Issue: 04B • Printing Date: January 28, 2009. Printed in Canada. The information contained in this User Manual is subject to change without notice or obligation.
- Page 3 Important Regulatory and Safety Notices to Service Personnel Before using this product and any associated equipment, refer to the “Important Safety Instructions” listed below so as to avoid personnel injury and to prevent product damage. Products may require specific equipment, and /or installation procedures be carried out to satisfy certain regulatory compliance requirements.
- Page 4 ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE” Do not block ventilation openings. Install in accordance with manufacturer’s instructions. Do not install near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not use this apparatus near water.
- Page 5 If the module does not appear to be working properly, please contact Technical Support using the numbers listed under the “Contact Us” section on the last page of this manual. All RossGear GearLite products are covered by a generous 3-year warranty and will be repaired without charge for materials or labor within this period.
-
Page 7: Table Of Contents
Function Setup and Configuration Menu Table ....3-6 Function Menu Notes ............3-8 Specifications In This Chapter................4-1 Technical Specifications............ 4-2 Service Information In This Chapter................5-1 Warranty and Repair Policy ..........5-1 Ordering Information In This Chapter................6-1 Contents • i ADR-9039 User Manual (Iss. 04B) - Page 8 • Contents ADR-9039 User Manual (Iss. 04B)
-
Page 9: Introduction
GearLite compact, self-contained modular products. Supporting 525 and 625 analog composite video reference, the ADR-9039 is the ideal analog to SDI reference converter for virtually all composite reference to digital reference conversion requirements. -
Page 10: Functional Block Diagram
Functional Block Diagram Figure 1. Simplified Block Diagram of ADR-9039 Functions Features The ADR-9039 Analog Composite to SDI Reference Converter has the following features: • Supports 525 and 625 composite analog video input signals • Output timing adjustable from 0 to 1 frame •... -
Page 11: Installation
Unpacking Unpack each ADR-9039 module you received from the shipping container and check the contents against the packing list to ensure that all items are included. If any items are missing or damaged, contact your sales representative or Ross Video directly. - Page 12 BNC connectors. Velcro Strips The included Velcro strips allow the GearLite module and power supply to be affixed to a permanent location during use and easily removed for adjustments. Carefully consider the installation location before proceeding; the adhesive is very aggressive and is not easily removed.
- Page 13 • remove the protective backing film from the top of the adhesive strips • press the module into position on the mounting surface 4. To mount the power adaptor, apply the remaining mating Velcro strip set, repeating the previous steps. Installation • 2-3 ADR-9039 User Manual (Iss. 04B)
- Page 14 Two pads can be used at the rear of the module to help support it when mounted in the GRF-9000 GearLite Rack Frame (see Optional Mounting Accessories). 2-4 • Installation...
- Page 15 90° angle. Figure 4. BMP-9000 90° Mounting Bracket GRF-9000 The GRF-9000 GearLite Rack Frame is a rack mounting frame system for GearLite modules. The mounting system provides convenient organization for up to nine GearLite modules in only a 2RU space.
- Page 16 The flat metal plate and small plastic label (see Figure 6) included with every GearLite module are used to mount a module into the GRF-9000. Complete instructions are included in the GRF-9000 User Manual. Figure 6. Flat Metal Plate and Label Positions for GRF-9000 Mounting 2-6 •...
-
Page 17: Setup And Operation
• Function Menu Notes Cable Connections Connect the analog input and SDI output cables to the ADR-9039 according to the designations indicated on the chassis label. The input is internally terminated at 75 Ohms. It is not necessary to terminate unused outputs. -
Page 18: Power Adaptor And Supply
9000 provides regulated +5V DC (5%) @ up to 2A. The DC power cord has a locking connector that securely fastens into the power supply DC jack on the ADR-9039. The ADR-9039 has a standard miniature power jack (center pin positive). If using an adaptor other than the PS-9000, ensure that the polarity is correct and that the voltage is +5V DC regulated to 5% and it can supply sufficient current for the ADR-9039. -
Page 19: User Controls
The following are general descriptions of the user controls identified in Figure 9, presented in normal operating sequence. Figure 9. ADR-9039 Front Edge Operational Components Status and Selection LEDs The front panel of the module has four LEDs (Down, Up, Error, and OK) that display the status of the input signals, and indicate menu function and configuration selections. - Page 20 • LED will be continually lit when greater than or equal to the mid point. • LED will be unlit when the selected menu item is adjusted below the mid point. 3-4 • Setup and Operation ADR-9039 User Manual (Iss. 04B)
-
Page 21: Setup And Configuration
Setup and Configuration Use the Function Select switch and the Down and Up buttons to configure the ADR-9039 to convert analog video signals to SDI. Settings are described in Table 2. General Operating Rules Please note the following important operating rules for the ADR-9039: •... -
Page 22: Function Setup And Configuration Menu Table
● Unlit LED display ☼ Flashing LED display Note Functions listed in the Function column as being stored in memory ( ), always power up in the last known state. 3-6 • Setup and Operation ADR-9039 User Manual (Iss. 04B) - Page 23 Set Min ☼ ● Delay Not Reset ○ ● 625 (PAL) ● ○ Reference 525 (NTSC) ○ ● Standard Auto Select * ○ ○ Default Default - (h) ● ● Setup and Operation • 3-7 ADR-9039 User Manual (Iss. 04B)
-
Page 24: Function Menu Notes
Use this menu to reset both the H Delay and V Delay values to 0 (zero). Reference Standard Use this menu to select the input reference signal standard. You can set the ADR-9039 to lock to 525 only, 625 only, or automatically detect either format from the input signal. Default Use this menu to reset all settings to factory defaults. -
Page 25: Specifications
Specifications In This Chapter This chapter contains the Technical Specifications table. Specifications • 4-1 ADR-9039 User Manual (Iss. 04B) -
Page 26: Technical Specifications
Technical Specifications Table 3. ADR-9039 - Technical Specifications Category Parameter Specification Number of Inputs Composite Black (NTSC or PAL Analog Signal Standards (B/G) Video Input Input Impedance 75Ω terminating Return Loss >41dB to 5MHz Number of Outputs SMPTE 259M-C (270Mb/s, 525/625... -
Page 27: Service Information
This chapter contains Warranty and Repair Policy information. Warranty and Repair Policy The RossGear ADR-9039 is warranted to be free of any defect with respect to performance, quality, reliability, and workmanship for a period of THREE (3) years from the date of delivery to the customer. In the event that your RossGear... - Page 28 In Case of Problems Should any problem arise with your RossGear ADR-9039, please contact the Ross Video Technical Support Department. (Contact information is supplied at the end of this publication.) A Return Material Authorization number (RMA) will be issued to you, as well as specific shipping instructions, should you wish our factory to repair your RossGear ADR-9039.
-
Page 29: Ordering Information
(Front of rack frame for mounting up to nine GearLite modules in 2RU space) Your ADR-9039 Analog Composite to SDI Reference Converter is part of the GearLite line of the RossGEAR family of products. Ross Video Limited offers a full line of RossGEAR digital terminal equipment including distribution, conversion, monitoring, synchronizers, encoders, decoders, amplifiers, keyers, switches, as well as analog audio and video products. - Page 30 Notes 6-2 • Ordering Information ADR-9039 User Manual (Iss. 04B)
- Page 31 Notes Ordering Information • 6-3 ADR-9039 User Manual (Iss. 04B)
- Page 32 Contact Us Contact our friendly and professional support representatives for the following: • Name and address of your local dealer • Product information and pricing • Technical support • Upcoming trade show information General Business Office 613 • 652 • 4886 and Technical Support PHONE After Hours Emergency...