Subscribe to Our Youtube Channel
Related Manuals for lifeSMART MSA201 Z
Summary of Contents for lifeSMART MSA201 Z
- Page 1 毫米波雷达人体存在感应器 (ZigBee) 型号: MSA201 Z 使用手册 Human Presence Sensor (Radar Detector, ZigBee) Model: MSA201 Z User Manual...
- Page 3 3-4m 2.5-3.5m 2.5-3.5m...
- Page 5 1.初始化： 上电后通电指示灯慢闪20秒后关闭， 在此期间传 感器不与通信模块通讯， 不探测外界移动信号。 初始化完毕 后进入正常工作状态。 2.本品需配合智慧中心和LifeSmart APP使用， 手机扫描下 方二维码下载APP。 3.配网说明： 传感器通电初始化 （指示灯慢闪20秒） 后进入配 网状态， 配网状态下指示灯快闪， 打开LifeSmart APP， 选择 添加新设备-传感器-人体存在感应器(ZigBee） (MSA201Z), 按照APP提示进行配网操作。 设备配网成功后， LED指示灯常亮10秒； 如入网失败， LED 指示灯长灭10秒。 4.APP说明 指示灯开关 开关打开后， 检测到有人， 感应器指示灯会 闪烁， 关闭， 检测到有人时， 指示灯不闪烁。 探测灵敏度设置 灵敏度选择与实际应用空间成正比关系， 一...
- Page 6 1. Attention The product shall be installed by a professional electrician. Please If a pet passes by in the detection area, it may trigger the sensor. disconnect the power before installation and wiring. Before the The sensor should be installed far away from wireless devices product is powered on, please confirm that the input voltage such as network switches and routers, and installation interval range meets the requirements of the manual.
-
Page 7: Product Introduction
70%/80%/90%/100%,Set via APP nance output. The human body state and illuminance signals Hold Time (Note 2) 30s/1min/2min/3min/5min/ are inserted into the LifeSmart system as a data acquisition 10min/20min/30min, Set via APP unit to intelligently control electronic equipment such as Detection Range... -
Page 8: Installation Instruction
6. Structure 7. Wiring Indicator light Sensor Antenna Daylight sensor Pairing Button 8. Installation Instruction 1) Cut a hole of 55mm on the ceiling. 2) Open cover by small straight screw. 3) Loosing clamp and wiring. 4) Screw clamp and put the cover. 5) Open spring clip outward and install. - Page 9 Detection 10% sensitivity is recommended for 0.7x0.7m sensitivity space, 20% sensitivity is recommended for 2) This product is compatible with LifeSmart Smart Station and settings 1.4x1.4m space, and so on, 100% sensitivity is recommended for 7x7m space. APP. Scan the QR code below to download the APP.
- Page 10 Fault Cause Remedy Microwave can penetrate glass, wood and other Reduce the detection area. The sensor is non-metallic materials. self-triggered The sensor is installed close to the wireless device. Installed the sensor 0.5 meters away from the wireless devices. or the load will Make sure that there are no other motion signals in the space, permanently There are vibration or jitter signals in the installation...
Need help?
Do you have a question about the MSA201 Z and is the answer not in the manual?
Questions and answers