The information can be found on the rating plate. Warning / Caution-Safety information General information and tips Environmental information VISIT OUR WEBSITE: To get usage advice, brochures, trouble shooter, service and repair information: www.smeg.com/services/customer-service CONTENTS 1. SAFETY INFORMATION...................2 2. SAFETY INSTRUCTIONS.................4 3. INSTALLATION....................6 4. PRODUCT DESCRIPTION................7 5.
Page 3
1.1 Children and vulnerable people safety This appliance can be used by children aged from 8 years • and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
If the supply cord is damaged, it must be replaced by the • manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. WARNING: Knives and other utensils with sharp points • must be loaded in the basket with their points down or placed in a horizontal position.
Page 5
(water meters, etc.), let the water flow until • Please note that self-repair or non- it is clean and clear. professional repair can have safety • Ensure that there are no visible water consequences and might void the leaks during and after the first use of the guarantee.
3. INSTALLATION appliance and may cause an injury. If the WARNING! plastic cover is damaged, contact the Authorized Service Centre to replace it with Refer to Safety chapters before the new one. installation. For detailed installation information, see the installation instruction supplied with the appliance.
4. PRODUCT DESCRIPTION Ceiling spray arm Lower basket Upper spray arm Upper basket Lower spray arm Cutlery drawer Filters The graphic is a general overview. Rating plate For more details, refer to other chapters Salt container or documents provided with the Air vent appliance.
Option buttons programme button 5.1 Display A. Indicators B. Time indicator 5.2 Indicators Indicator Description "Before Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to first use" "Before first Salt indicator. It is on when the salt container needs refilling. Refer to use"...
cutlery with normal soil. This is the (Extreme) standard programme for test institutes. This option improves the dishwashing results (Auto) of the selected programme. It increases the wash temperature and duration. This programme automatically adjusts the dishwashing cycle to the type of load. (Crystal) The appliance senses the degree of soil and the amount of dishes in the baskets.
7.2 Information for test institutes In your request, include the model from the rating plate. To receive the necessary information for conducting performance tests (e.g. according to: EN60436 ), contact the manufacturer. 8. BASIC SETTINGS You can configure the appliance by changing basic settings according to your needs.
Page 12
• The appliance returns to the basic How to enter setting mode settings list. You can enter setting mode before starting a 5. Press and hold simultaneously programme. You cannot enter setting mode while the programme is running. for about 3 seconds to exit setting mode.
Page 13
Regardless of the type of detergent used, additional 4 litres and the total energy set the proper water hardness level to consumption of a programme by additional 2 keep the salt refill indicator active. Wh. The rinsing of the softener ends with a complete drain.
CAUTION! Do not try to close the appliance door within 2 minutes after automatic opening. This can cause damage to the appliance. CAUTION! If children have access to the appliance, we advise to deactivate Dry Assist. The automatic opening of the door may pose a danger.
CAUTION! The compartment (A) is for rinse aid only. Do not fill it with detergent. CAUTION! Only use rinse aid designed specifically for dishwashers. 6. Turn the cap clockwise to close the salt container. 1. Press the release button (D) to open the lid (C).
Page 16
1. Press the release button (B) to open the lid (C). By default, options must be activated 2. Put the detergent, in powder or tablets, in every time before you start a programme. the compartment (A). 3. If the programme has a prewash phase, It is not possible to activate or put a small quantity of detergent on the deactivate options while a programme is...
The appliance returns to the programme If the door is opened for more than 30 selection. seconds during the drying phase, the running programme ends. It does not If you cancel the delay start, you have happen if the door is opened by Dry to select the programme again.
Page 18
11.2 Using salt, rinse aid and 11.4 Before starting a programme detergent Before you start the selected programme, make sure that: • Only use salt, rinse aid and detergent designed for dishwasher. Other products • The filters are clean and correctly can cause damage to the appliance.
12. CARE AND CLEANING • Do not use abrasive products, abrasive WARNING! cleaning pads, sharp tools, strong chemicals, scourer or solvents. Before any maintenance other than • Wipe clean the door, including the rubber running the programme Self Clean, gasket, once a week. deactivate the appliance and disconnect •...
Page 20
5. Make sure that there are no residues of food or soil in or around the edge of the 1. Turn the filter (B) counterclockwise and sump. remove it. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides.
Page 21
CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 12.6 Cleaning the lower spray arm We recommend to clean the lower spray arm regularly to prevent soil from clogging the holes. Clogged holes can cause unsatisfactory washing results.
2. Move the upper basket to the lowest level 5. To install the spray arm (C) back, insert to reach the spray arm more easily. the mounting element (B) in the spray 3. To detach the spray arm (C) from the arm and fix it in the delivery tube (A) by delivery tube (A), turn the mounting turning it clockwise.
Page 23
Problem and alarm code Possible cause and solution The appliance does not fill with • Make sure that the water tap is open. water. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. The display shows •...
Page 24
Problem and alarm code Possible cause and solution The remaining time in the display • This is not a defect. The appliance is working correctly. increases and skips nearly to the end of the programme duration. Small leak from the appliance •...
Page 25
Problem Possible cause and solution Poor drying results. • Tableware was left for too long inside the closed appliance. Acti‐ vate the function Dry Assist to set the automatic opening of the door and to improve the drying performance. • There is no rinse aid or the dosage of rinse aid is not sufficient.
Problem Possible cause and solution Limescale deposits on the table‐ • The level of salt is low, check the refill indicator. ware, on the tub and on the inside • The cap of the salt container is loose. "The water softener" of the door.
database using the link https:// For more detailed information about the eprel.ec.europa.eu and the model name and energy label, visit www.theenergylabel.eu. product number that you can find on the rating plate of the appliance. Refer to the chapter "Product description". 15.