Advertisement
Quick Links
Advertisement
Related Manuals for Impact Acoustics Chatpod 700
Summary of Contents for Impact Acoustics Chatpod 700
- Page 1 90min Assembly instructions Chatpod 700...
- Page 2 Insert the supply cable and the 3.5m cable into the H-distributor until it click into place. supply cable 5m click Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 3 Hold the sides until the top is assembled. Pin the top together with the sides, pull the cable through the top from the right side. click cable of the side Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 4 3 Insert the eight connecting rods. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 5 4 Insert the wooden dowels into the holes. Join the two back panel elements and pull them together with the connectors. Do the same with the front elements. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 6 Join the back wall with the sides, the bottom and the top. Secure the back panel by screwing the ten screws a few turns into the connecting rods. Insert the 3.5m cable into the H-distributor. 3.5m M6 x 40mm Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 7 Place the honeycomb cardboard blocks under the cardboard supports of the base. Make sure that the bottom sits stably on the blocks and that the blocks protrude a few centimeters to the sides. Feed the cable through the hole in the base. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 8 Hold the sides until the lid is assembled. connect the top together with the sides. Insert the cable from the side in the H-distributor. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 9 8 Assemble the connecting frame with the wooden dowels. Pull the frame together with the connec- tors. Two connectors are needed for each of the lower corners. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 10 Use the set screws for this purpose. Tighten the connecting rods as far as they will go. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 11 10 Join the front with the sides, the bottom and the top Tighten the front with the M6x40mm screws, which must be countered on the opposite side. M6 x 40mm Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 12 Insert the two cables into the H-distributors from the sides. Remove the eight honeycomb card- board blocks. Align the chatpod using the leveling feets. Place the four outer panels on the top. Plug the power cord into the socket. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 13 12 Apply the double-sided adhesive tape to the floor as shown. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 14 13 Glue the carpet to the floor, making sure that the cut-outs match the holes in the floor. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 15 Remove the release paper of the double-sided tape and apply some additional glue dots with the installation glue provided. Make sure that the panels are completely flush with the top and side. Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 16 15 Screw the cable channel and the two brackets onto the table top. 4x16mm Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 17 Level and centre the table top and drill the holes for the table attachment in the back wall. A stepped drilling is necessary, first with a 7mm drill bit 6mm deep and then with a 5mm drill bit a total of 32mm deep. 7x35mm M6x12mm Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 18 Screw the benches onto the floor with the 7x35mm screws. Carefully loosen the cover of the socket. Connect the socket with the supply cable. Insert the socket into the hole. Align it and tighten it. Place the insert and snap the cover back into place. 7x35mm Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)
- Page 19 3 mm hex key. Make sure that the handle is mounted with the pre-mounted square pin in the inside of the chatpod. Well done! Chatpod 700 Impact Acoustic AG, Bodenhof 4, 6014 Luzern (Switzerland)