Advertisement
Quick Links
Instructions-Parts List
™
GL-1
For Single–Line Parallel Automatic Lubrication Systems.
Important Safety Instructions
Read all warnings and instructions in this manual and related automatic
lubrication system instruction manuals. Save all instructions.
SKIN INJECTION HAZARD
Fluid from the injector, leaks, or ruptured components
can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid
injected into the skin might look like just a cut, but it is
a serious injury. Get immediate surgical treatment.
Fluid splashed in the eyes or on the skin can also
cause serious injury. The equipment may be pressur-
ized already, or it could become pressurized by an
automatic lube cycle initiated by Lubrication Controller
(timer). Disconnect power to the timer, and disconnect
the air supply to the pump module to ensure that the
system is depressurized. See the pressure relief pro-
cedure in the pump manual included with your
automatic lubrication system.
GL-1 Injector Models
Part No.
Injector, GL–1, one point
114901
Injector, GL–1, two point
114902
Injector, GL–1, three point
114903
Injector, GL–1, four point
114904
Injector, GL–1, five point
114905
Injector, GL-1, six point
117206
Injector, GL–1, replacement
114909
Injector, SST, replacement
25N109
Injectors
Description
Model 114903 Shown
Dimension A
Dimension B
2.48 in. (63.0 mm)
3.00 in. (76.0 mm)
1.25 in. (31.7 mm) 4.23 in. (107.5 mm)
2.50 in. (63.4 mm) 5.47 in. (139.0 mm)
3.75 in. (95.1 mm) 6.71 in. (170.5 mm)
4.99 in. (126.8 mm) 7.90 in. (202.7 mm)
308953ZAC
EN
Bare Manifold
Part No.
114911
114912
114913
114914
114915
118206
Advertisement
Related Manuals for Graco GL-1 114901
Summary of Contents for Graco GL-1 114901
- Page 1 Instructions-Parts List ™ GL-1 Injectors 308953ZAC For Single–Line Parallel Automatic Lubrication Systems. Important Safety Instructions Read all warnings and instructions in this manual and related automatic lubrication system instruction manuals. Save all instructions. Model 114903 Shown SKIN INJECTION HAZARD Fluid from the injector, leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation.
-
Page 2: Installation Instructions
Installation Instructions Installation Instructions The reference letters used in the following instructions 7. Run the system at full output and verify that all refer to the figure on page 3. injectors are cycling. 8. Adjust injector volume output. see Volume Adjust- •... -
Page 3: Injector Service Parts
(for connecting the injector outlets to increase output) Graco Part No. 241234: Injector Repair Kit (See parts in Injector Service Parts.) Graco Part No. 25D336: Cap kit (see page 4) Spacer Kits - 10 Pack: See Table and instructions, page 4. - Page 4 Injector Service Parts Injector Cover Kit 17L754 Spacer Kits Item Description Spacer Kit Table O-ring Output Target Output Target Ratio Part From From Installation Instructions color cu. in. minimum 1. Apply a light coating of transparent lubricant to the 0.01 0.10 inside of the cap (21).
-
Page 5: Technical Data
Technical Data Technical Data Maximum operating pressure 3500 psi (24 MPa, 241 bar) Suggested operating pressure 2500 psi (17 MPa, 172 bar) Reset pressure 600 psi (4.1 MPa, 41 bar) Output volume per cycle adjustable*: 0.008 to 0.08 in. Wetted parts carbon steel, stainless steel, UHMWPE, fluoroelastomer Recommended fluids N.L.G.I. -
Page 6: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.