Table of Contents
Advertisement
Operating th
There are five buttons for menu operations on the front of
the monitor. To display the main menu, first press MENU.
The buttons you can use appear at the bottom of the menu
screen.
Functions of the buttons
Button
To select menu
To adjust menu item
item
.
selected
MENU
return to the
return to the previous
EXIT
previous menu
menu
ENTER
decideaselected
__ select an item
SELECT
item
t
move the cursor
increase selected value
(>) upwards
4
move the cursor
decrease selected value
; - |
(») downwards
RESET
reset current adjustment
value to the factory
setting
front of monitor
B/
C/
LINE/
EXT
COMPONENT _ SDI
RGB
SYNC
BLUE
UNDER
HV
16:9
ONLY
SCAN
DELAY
RESET
buttons for
button
menu
;
operations
=|
Main menu
Select an item and press ENTER to go to the following
menu.
[ro]
CHROMA
SET UP menu
Set to ON to adjust the internal decoder for CHROMA
and PHASE (NTSC signal only) after AUTO ADJUST
([6)).
[OFF]
[3] COLOR TEMP/BAL menu
Select the color temperature from among 6500K, 9300K
and USER. USER is set to 6500K in the factory setting.
You can adjust or change the color temperature in USER
mode (a measuring instrument is needed).
[6500K]
[4] USER CONFIG 1 menu
Select an item to adjust. To go to the USER CONFIG 2
menu, select NEXT PAGE.
[5] USER CONFIG 2 menu -
Select an item to adjust. To go to the USER CONFIG 1
menu select PREVIOUS PAGE.
[6] AUTO ADJUST screen
Select the color bar signal (full, SMPTE, EIA) and press
ENTER to start auto adjusting for CHROMA SET UP
(NTSC signal only).
ADJUST GAIN screen
Adjust GAIN in USER mode.
ADJUST BIAS screen
Adjust BIAS in USER mode.
[9] COLOR TEMP RANGE menu
Select the color temperature range in USER mode.
[5000K-10000K]
COLOR SYSTEM DISPLAY menu
Select the color system display mode. In AUTO, the kind
of color system being used appears on the screen each
time you change the signal input.
[AUTO]
358 TRAP FILTER menu
Color spill or color noise may be eliminated if you select
ON (NTSC signal only).
[OFF]
12} SUB CONTROL screen
You can finely adjust the controls on the front panel.
CONTRAST, BRIGHT, CHROMA and PHASE control
has a click at the center of its adjustment range. You can
adjust the setting of the click position with this feature.
USER PRESET menu
You can preset each control to a desired level and set it.
If you set USER PRESET to ON, the REMOTE indicator
lights up and the controls on the front panel do not
work. The monitor operates with the internal memory
settings. For adjustment, select PRESET ADJUST.
[OFF]
(4] PRESET ADJUST screen
Adjust CONTRAST, BRIGHT, CHROMA, PHASE,
VOLUME, APERTURE in USER PRESET.
V HOLD screen
Adjust the vertical hold if the picture rolls vertically.
When you cannot read the display, select the input that
is not connected.
(16) COMPONENT LEVEL menu
Select the component level from among three modes.
N10/SMPTE
for 100/0/100/0 signal
BETA 7.5
for 100/7.5/75/7.5 signal
BETA 0
for 100/0/75/0 signal
[N10/SMPTE]}
NTSC SETUP LEVEL menu
Select the NTSC setup level from two modes. The 7.5
setup level is mainly used in north America. The 0 setup
level is mainly used in Japan.
[0]
ACC menu
Set ACC (Auto Color Control) circuit on or off. When the
fine adjustment is needed, set ACC to OFF. Normally set
it to ON.
[ON]
LANGUAGE menu
You can select the menu language from among the five
languages (English, German, French, Italian, Spanish) on
the menu.
[ENGLISH]
{I ] indicates the factory setting position.)
ysij6ug
Advertisement
Table of Contents
