Related Manuals for FMG UA195/340
Summary of Contents for FMG UA195/340
- Page 1 EQUIPMENT OPERATORS MANUAL UA195/340-UA300/620 ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI TEL. +358 (0)20 1984 020 ● FAX +358 (0)20 1984 029...
- Page 2 OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO 730:2020. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed att följande maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO 730:2020.
- Page 3 Warranty is not covering damages due to misuse of product or use in the purposes where it has not been designed, lack of services or product has been modified without the permission of FMG. Wearing of the normal usage is not covered by the warranty.
- Page 4 In case of that kind need please contact your FMG seller or factory. Use only genuine FMG spare parts for optimum performance from your tractor and U-plough. Spares will be sold through the FMG seller.
-
Page 5: Table Of Contents
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH TABLE OF CONTENTS TABLE OF CONTENTS ............................ 5 SAFETY INSTRUCTIONS ........................6 CONSTRUCTION ............................. 8 TECHNICAL SPECIFICATIONS ......................9 U-PLOUGH USE............................9 4.1. Using area ............................9 4.2. Instructions ............................9 4.3. U-plough use ..........................10 SERVICE .............................. -
Page 6: Safety Instructions
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 1. SAFETY INSTRUCTIONS This section summarizes the regulations that must always be followed when working with the U- plough. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regulations that apply to different types of working sites and existing road traffic laws must always be observed. - Page 7 OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH WARNING Observe Operators Manual instructions while working. WARNING Pay attention to other road users. IMPORTANT Lower implement always down to ground and stop the engine before leaving the cab. IMPORTANT Do not leave the implement resting on the hydraulics when serving or checking, use mechanical support.
-
Page 8: Construction
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 2. CONSTRUCTION 1. Machine bracket (adapter) 2. Joint frame 3. Main wing 4. Side wing 5. Support leg 6. Side wing cylinder 7. Main wing cylinder Page 8... -
Page 9: Technical Specifications
Working width Height Weight Main wing Side wing (cm) (cm) (kg) turning angle turning angle 187 – 357 UA195/340 +/- 37 +/- 175 187 – 382 UA195/370 +/- 37 +/- 175 248 – 418 UA245/410 1065 +/- 37 +/- 175 248 –... -
Page 10: U-Plough Use
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 4.3. U-plough use Working position of plough is correct when frame is in the upright position (Picture 1), especially when use side wings. Picture 1. Plough frame in the upright position IMPORTANT When plough is new take care that air from hydraulic system will be eliminated by turning cylinders against to the limit stoppers couple of the time. -
Page 11: Daily Service
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 5.1. Daily service - Check all the blades - Check tightness of the fastening screws - Test drive all the movements - Clean the equipment in the end of the working day 5.2. Weekly service - Lubricate all the nipples - Check that there are no leakages 5.3. -
Page 12: Lubricating Points
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 5.5. Lubricating points Lubricate nipples shown in the picture. Clean the top of the nipple before lubrication. - Central joint grease nipples (2) - Cylinder grease nipples (8) - Sliding frame and connecting frame grease nipples (8) - Side wing joint grease nipples (8) Page 12... -
Page 13: Screws To Be Tighten
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 5.6. Screws to be tighten Tighten all the screws after 10 hours´ drive and after that between 500 working hours. - Attaching frame screws - Tightening screw of the support legs - Tightening screws and nuts of the blade frame and the spring - All the blade screws Page 13... -
Page 14: Electric Valve And Side Lights Connection
OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH 6. ELECTRIC VALVE AND SIDE LIGHTS CONNECTION 1.Side lights 4.Valve 1 5.Valve 2 6.Ground 7.Ground Page 14... - Page 15 OPERATORS MANUAL D0004G (ce 17461→) U-PLOUGH LLP FARM MACHINERY GROUP OY LEVYTIE 4 74510 IISALMI, FINLAND PUH. +358 (0)20 1984 020 FAX +358 (0)20 1984 029 www.fmg.fi Page 15...