Page 1
EQUIPMENT OPERATORS MANUAL PA300-PA390 ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI PUH. +358 (0) 20 1984 020 ● FAX +358 (0) 20 1984 029...
Page 2
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO730-1. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed att tillförda maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO730-1.
Page 3
Losses in income, costs and loosen working hours caused by the defected part is not covered by the warranty. Warranty repairs should be done by the FMG service dealer or service dealer appointed by the manufacturer. In case the defects shown in reclamation is not valid or if case otherwise is not in the warranty area FMG has right to reject from the compensation.
Page 4
In case of that kind need please contact your FMG seller or factory. Use only genuine FMG spare parts for optimum performance from your tractor and plough. Spares will be sold through the FMG seller.
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 1. SAFETY INSTRUCTIONS This section summarizes the regulations that must always be followed when working with the plough. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regulations that apply to different types of working sites and existing road traffic laws must always be observed.
Page 7
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH WARNING Observe the manufacturer's instructions while working. WARNING Pay attention to other road users. IMPORTANT Always lower the implement and stop the engine before leaving the cab. IMPORTANT Never service or clean an implement that is resting on the hydraulics. Use mechanical support.
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 4.3. Butterfly plough use: Engage plough to the working machine that floating bar is in the mid position and plough is in the balanced position (Picture 2). Picture 2. Floating bar in the mid position In case the adapter is wrong change adapter and ensure that screws are tightened well.
Page 11
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH Picture 3. Plough frame in the upright position In normal working position hydraulic suspension cylinder is in the minimum position. Blade angle is possible to adjust by moving suspension cylinder to another hole (3 different alternative) (Picture 4). Picture 4.
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 4.4. Pressure adjustment of the hydraulic suspension Factory adjustment of hydraulic suspension is 110 bar. Factory adjustment will be reached by tightening screw fully and opening it 6,5 round back. Picture 5. Pressure adjustment of the hydraulic suspension Releasing the adjustment screw (Picture 5), tightness will go down and by tightening tightness go up.
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 5. HYDRAULIC SCHEMA 5.1. Butterfly plough with the standard hydraulic Picture 6. Butterfly plough with the standard hydraulic Sivu 13...
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 5.2. Butterfly plough with the 6/2 electric valve Picture 7. Butterfly plough with 6/2 electric valve Sivu 14...
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 6. SERVICE The most important thing to get maximum reliability is good service in time. Service costs are smaller compared to the repairing´s costs. Below mentioned service in- cludes all the lubrications and adjustments. 6.1. Daily service - Check all the blades - Check tightness of the fastening screws...
Page 16
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH When serving you should follow the service table also taking care of the previous services. Tightness of the screws should be checked also after the first drive. Lubricate also piston rods when leaving equipment to the storage place.
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 6.5. Lubrication Lubricate nipples shown in the picture (Picture 8). Clean the top of the nipple before lubrication. Picture 8. Lubrication Sivu 17...
OPERATORS MANUAL D0003D BUTTERFLY PLOUGH 6.6. Screws to be tighten Tighten all the screws after 10 hours´ drive and after that between 500 working hours. 1. Tightening nut of the main pin in the center 2. Tightening screw of the support leg 3.