AquaStar PURESTAR PS10 Installation And User Manual
Corona discharge ozone generation system
Hide thumbs
Also See for PURESTAR PS10:
- Installation (2 pages) ,
- Operation and maintenance manual (3 pages)
Table of Contents
Advertisement
Quick Links
PURESTAR
CORONA DISCHARGE OZONE GENERATION SYSTEM
INSTALLATION AND USER'S GUIDE
MODEL # PS10
FOR YOUR SAFETY
Read, understand and follow all warning notices and instructions before
installing, using, or servicing this system. Failure to follow warning notices
and instructions may result in property damage, serious injury, or death.
SAVE THESE INSTRUCTIONS
P (877) 768-2717 - F (877) 276-POOL - info@aquastarpoolproducts.com - www.aquastarpoolproducts.com - © 2023 AquaStar Pool Products, Inc. - IN034-120123
U.S. Patents www.aquastarpoolproducts.com/patents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AquaStar PURESTAR PS10
Summary of Contents for AquaStar PURESTAR PS10
- Page 1 Failure to follow warning notices and instructions may result in property damage, serious injury, or death. SAVE THESE INSTRUCTIONS P (877) 768-2717 - F (877) 276-POOL - info@aquastarpoolproducts.com - www.aquastarpoolproducts.com - © 2023 AquaStar Pool Products, Inc. - IN034-120123 U.S. Patents www.aquastarpoolproducts.com/patents...
- Page 2 PureStar Installation and User’s Guide - AquaStar Pool Products...
-
Page 3: Installation Requirements
Attention Installer: Read this manual completely before attempting installation. Failure to follow these instructions could result in injury or death and will void the product warranty. Consult AquaStar Pool Products with any question regarding this product. This guide must be left with the pool owner. -
Page 4: Section 1. Overview
Pool / Spa 2. PureStar, Inlet Air Filter 3. PureStar, Blank Tube 4. PureStar, 12V Tranformer 5. Union/Nut Kit, 2.5" Nut, 2" Soc, 2.5" Soc., & O-rings Typical installation with heater PureStar Installation and User’s Guide - AquaStar Pool Products... -
Page 5: Plumbing Connections
These O-Rings come pre- in the Full Speed row of the Operation Log, on page 6. lubricated. Place the “PureStar Blank Tube” between the unions and hand tighten the union nuts. AquaStar Pool Products - PureStar Installation and User’s Guide 5... -
Page 6: Normal Operation
Air Intake Location Water Chemistry It is important to regularly test for chlorine or bromine to ensure that proper sanitizer residual is present in the pool or PureStar Installation and User’s Guide - AquaStar Pool Products... -
Page 7: Section 3. Troubleshooting
Light continues to "Slow Pulse" after Pulse” state indefinitely after the pump pump has stopped has stopped, an electrical failure has Electrical failure occurred. Contact AquaStar Pool Products Technical Support at (877) 768-2717. AquaStar Pool Products - PureStar Installation and User’s Guide 7... - Page 8 30 seconds, plug the unit back in. 3 Flash Error Code = Voltage high Power supply failure If flashing continues, contact AquaStar Pool Products Technical support at (877) 768-2717 and report error code. PureStar Installation and User’s Guide - AquaStar Pool Products...
-
Page 9: Contact Information
If problem persists contact working temperature AquaStar Pool Products Technical support at (877) 768-2717 and report error code. Contact Information For Technical Assistance: Call: 877-768-2717 Visit: www.aquastarpoolproducts.com Email: Info@aquastarpoolproducts.com AquaStar Pool Products - PureStar Installation and User’s Guide 9... -
Page 10: Limited Warranty
Customer following the procedures set forth below, AquaStar will, at its option, repair or replace such item or part at its own cost and expense. AquaStar’s maximum obligation under this warranty is limited to the repair and replacement of the PS10 Kit. - Page 11 AquaStar Pool Products - PureStar Installation and User’s Guide 11...
- Page 12 AquaStar Pool Products, Inc. 2340 Palma Drive Ventura, CA...
Need help?
Do you have a question about the PURESTAR PS10 and is the answer not in the manual?
Questions and answers