Table of Contents
Advertisement
a When the time has elapsed, a signal tone sounds. A
notification appears on the display confirming that
the operation has finished.
Once the cooking time has elapsed:
10.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If condensation has formed in the cooking compart-
11.
ment, dry the cooking compartment.
→ "Drying", Page 24
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 19
Changing the microwave output
You can change the microwave output at any time.
Press
on the display.
1.
Press the microwave output
2.
Use the setting ring to set the microwave output.
3.
To confirm the change, press
4.
a The change is applied.
Changing the cooking time
You can change the cooking time at any time.
Press
on the display.
1.
Press the cooking time
2.
3.
Use the setting ring to change the cooking time.
To confirm the change, press
4.
a The change is applied.
10.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
Dishes
11 Dishes
The "Dishes" operating mode helps you to use your ap-
pliance to prepare different meals by selecting the op-
timum settings automatically.
11.1 Cookware for dishes
The cooking result depends on the composition of the
meat and the size of cookware.
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300 °C. Glass or
glass ceramic cookware is best. The joint should cover
approx. 2/3 of the cookware base.
Cookware made from the following material is not
suitable:
¡ Bright, shiny aluminium
¡ Unglazed clay
¡ Plastic or plastic handles
Note: For some dishes, the appliance switches on the
microwave. A notification appears in the display stating
that you should use cookware that is suitable for mi-
to switch the ap-
.
on the display.
.
on the display.
¡ → "Preventing material damage", Page 6
¡ → "Microwave output settings", Page 11
¡ → "Cookware and accessories with microwave",
Page 15
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 16
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press
"Added microwave".
3.
Use the setting ring to set the microwave output.
4.
5.
To confirm the set microwave output, press
the display.
Press
"Cooking time" and set the cooking time.
6.
7.
Press
to start the operation.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
8.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press
on the display.
1.
Press the microwave output
2.
Change or deactivate added microwave with the
3.
setting ring.
To confirm the change, press
4.
a The change is applied.
crowave use.
→ "Cookware and accessories with microwave",
Page 15
11.2 Setting options for the dishes
To cook the dishes perfectly, the appliance uses differ-
ent settings depending on the dish.
The display shows you the settings that are used. You
can adjust certain settings. Follow the instructions on
the display.
Note: The cooking result depends on the quality and
composition of the food. Use fresh and, ideally, chilled
food. Use frozen food straight from the freezer.
Tips and information about the settings
If you set a dish, the display shows relevant information
for this dish, e.g.:
¡ Suitable shelf position
¡ Suitable accessory or cookware
¡ Added liquid
Dishes en
on
to switch the ap-
.
on the display.
17
Advertisement
Table of Contents
