Table of Contents
Advertisement
Quick Links
User Manual
#)TRIPLETT
PS605 DC Power Supply (80V/5A/100W)
,s,os
nt fPt. ffT
6
1 1 1 1 1 11
1 1 11
11 11 11 11
I
111 11 111 11 ::
,,
1111 11
t
111
llllll lt 11 1
1111 111 II I
111111 111
111111 11111 I
1111 111 11 II
II
1 111 111 111
I II
U III I I
.
I I :
1 11 1 1 11
II II I
I I I I I I
I 11
l
1 1 t l l
1
I t i 1
11•••:,, ,1 1
t i
1 1 1 I :
I
ti
t i
, , I I
I
Ill
I I
I
I I I I
I I
I I
,,, , ,
I
I I
I
' I I
I I I I I I I
CE
Advertisement
Table of Contents
Related Manuals for Triplett PS605
Summary of Contents for Triplett PS605
- Page 1 I t i 1 11•••:,, ,1 1 1 1 1 I : , , I I User Manual #)TRIPLETT PS605 DC Power Supply (80V/5A/100W) ,s,os nt fPt. ffT I I I I ,,, , , ' I I I I I I I I I...
- Page 2 ： Warning Caution To avoid possible electric shock and personal safety problem, please follow the instructions below. Please read the following safety information carefully beforestarting to use the instrument. Uni-Trend will not be responsible for the personal safety Disclaimer and property damage caused by the user's failure to comply with the following terms.
-
Page 3: Waste Electrical And Electronic Equipment (Weee) Directive 2002/96/Ec
Do Not Please do not operating the instrument when open the cover and do not open the cover when the change the internal circuit. instrument is inoperating When the instrument is in operating, do not touch the bare connect wire, Do Not spare input terminal and the circuit is in testing. -
Page 4: Product Series
100W/60V=1.66A. When output voltage down to 20V, the max output current turns to 100W/20V=5A. The max output current of PS605 is 5A, if the current output voltage continue decrease , the max output current of PS605 still as 5A. -
Page 5: Specifications
Specifications Specification PS605 Voltage 0~60V Output Range Current 0~5A Power 100W Voltage <0.01%+3mV Load Regulation Current <0.01%+3mA Voltage <0.01%+3mV Power Supply Regulation Current <0.1%+3mA Voltage <0.05%+10mV Programming Accuracy Current <0.2%+2mA Voltage <0.05%+10mV Read-back Accuracy Current <0.2%+2mA Voltage <2.0mV rms Ripple and Noise Current <5.0mA rms... -
Page 6: Rear Panel
250V/5A spare fuse PS605 User’s Manual /Upper-computer Electronic file，download from the software official website Requirments of Power Supply PS605 power supply can only use under the power supply terms as the table below. Parameter Requirements Voltage AC110/ 220(±10%)V Frequency 50/60Hz Factory supply three-core power cable, please make sure power cable of three phase ... -
Page 7: Operating Environment
Trend Instrument Sale Department or the distributor. 2. Confirm whether the AC input voltage of PS605 complies with the standards of your country or region. Notice: Use 110V/220V switch on the rear panel to select input voltage. After confirming the above matters, power on... - Page 8 Voltage Setup 1) Push key to set voltage value; 2) Push to select the specific numeric field; 3) Rotating to enter the definited voltage parameter. Current Setup 1) Push key to set current value; 2) Push to select the specific numeric field; 3) Rotating to enter the definited current parameter.
-
Page 9: Enable Output
Enable Output 1) Push to enable power output function and the indicator light will be green. In the mean time, C.V/C.C indicator light will be green or red light according to the different output mode; 2) OUTPUT key indicator light will be off when OUTPUT function is disable. C.V/C.C indicator light will also be off. Keyboard Lock Lock keyboard function is prevent unauthorized worker or operating personnel form making accident operation. -
Page 10: Ovp Function
OVP Function 1) Long push key to set OVP function; 2) Push to select the specific numeric field and enter OVP parameters; 3) Push to enable OVP function; 4) When the OVP function set successfully, ☑ mark will shown beside OVP parameters. OCP Function 1) Long pushk key to set OVP function;... -
Page 11: Brightness Setup
Bepper Switch 1) Push to enter the setup interface, rotate to adjusting buzzer mode; 2) When the buzzer function is enable, keyboard sound is also turn on; when the buzzer function is disable, keuboard sound will be silent. Buzzer status will shown on the top screen. 3) Push to exit the setup page. - Page 12 Memory Group Setup 1) Push to enter setup interface; 2) Push to select Memory option; 3) Rotate to set memory group, the maximum range is 200; 4) Push to exit the setup page. Memory Group Voltage/Current Setup Set the specific output voltage/current point and select memory key M1~M3, push it to save the current setting. When user need to call the stored output voltage/current, enter the setup interface to select the specific memory group and then push memory key M1~M3 to call the specific stored output voltage/current.
-
Page 13: Language Setup
Output Mode Setup 1) Push to enter setup interface; 2) Push to select the output status bar; 3) Rotate to select Out State; 4) Output status symbol will shown on the top screen when output is finished; 5) Push to exit the setup page. Notice: When output function is operating, power supply should remain enable status. -
Page 14: Display Interface Information
Display Interface Information 1) Push to enter the setup interface; 2) Use left, right arrow key to select the IO Information option; 3) RS232 configuration information will shown on the right side of the screen. About 1) Push to enter the setup interface; 2) Push to select About field;... -
Page 15: Troubleshooting
Remote Sense Compensation Setup Before use Remote Sense compensation function, take off short connect terminal on the Remote Sense compensation terminal, connect load voltage positive terminal to compensation terminal S+ and load voltage negative terminal connect to compensation terminal S-. And then enable power output to turn on Remote Sense compensation function. That is, the output voltage of the DC power supply is the voltage of the load terminal. -
Page 16: Remote Communication
3. Connect the control line of RS232 to control power supply； 4. Activate the remote controlling application program； 5. Click Euqipments List, and double-click the power supply symbol of PS605 to enter the remote communication interface. Remote Control Interface & Operating Instructions... -
Page 17: Operating Steps
List Mode (Time Function) and Delayer Mode List Mode List mode can setup multiple testing program, it can set 48 groups of independentant voltage, current and parameter of output duration time. Delayer Mode Delayer mode can setup multiple testing program to control output status, which is set count to control output status is on or off, and the time interval of switch can also set by point to point. - Page 18 Menu introduction of list mode Cycle index：It divide into maximum inf and 1-999. A cycle period is start form setup origin point to end point. Push rotary knob to adjusting parameters. Count: It can set “001” - “048”, which is excute group from origin point to end point. Push rotary knob to adjusting point.
- Page 19 It presents power output status and delayer time of user configuration，it’s convenient to view the data. Protection setting：this function can set protection value of voltage, current and power, push rotary knob select “√”to turn on protection function； Cycle index：It divide into maximum inf and 1-999. A cycle period is start form setup origin point to end point; Count：It can set “001”...
Need help?
Do you have a question about the PS605 and is the answer not in the manual?
Questions and answers