Advertisement
4.1.3.7.
Tighten the end of the rope firmly after lowering.
4.1.3.8.
The pump can also be operated whilst suspended on a rope.
NOTE: For operation whilst suspended on the rope, DO NOT operate without the pressure hose. Avoid the pump twisting round its
longitudional axis.
4.2.
OPERATION
4.2.1.
Connect the pump to mains supply.
4.2.2.
The float switch can be set at different heights by affixing it to the slot on the unit's body, see illustration.
WARNING! The float switch must be able to move so that the submersible pump cannot run dry.
‰
5. MAINTENANCE
5.1.
BEFORE EVERY USE:
• check casing and cables for damage.
• check float switch for damage - lift and shake the switch to check the free movement of the contained metal balls.
5.2.
AFTER EVERY USE:
• clean the appliance: rinse with clean water, remove stubborn contamination with a brush and detergent. Submerge the pump in a
container with clean water and switch on for a short time to rinse the inside of the pump. Clean the suction area, see below.
5.3.
CLEANING THE SUCTION AREA
5.3.1.
Clean all accessible parts of the inside of the casing. Remove fibres which have wound round the rotor shaft by opening the
pressure connection. Remove stubborn contamination with a brush and detergent.
NOTE: Before using the pump again, first 'soak' it so that any possible dirt residues do not block the pump.
6. STORAGE
6.1.
If there is a risk of frost, dismantle the pump and accessories, clean and store them in a place protected from frost.
7. TROUBLESHOOTING
FAULT
Pump does not run.
Pump runs but does not
pump.
Delivery rate low
Pump runs very loudly.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
CAUSE
No mains voltage?
Motor overheats due to:
- liquid temperature too high
- pump blocked by foreign bodies
Residual current circuit breaker
(RCCB) triggered.
Motor defective.
Suction openings blocked.
Pump draws in air.
Pump blocked by foreign bodies.
Delivery height too great.
Pressure line diameter too small.
Pressure line blocked.
Suction openings blocked.
Pressure line kinked.
Pressure line leaks.
Pump draws in air.
sales@sealey.co.uk
Original Language Version
SOLUTION
Check cables, plug, socket and fuse.
Eliminate the cause of the overheating of the liquid (max.
temperature of liquid able to be pumped is 35°C).
Activate RCCB.
Contact qualified electrician if RCCB triggers again.
Contact Sealey service.
Rectify blockage.
Keep the pump at an angle while submerging.
Switch the pump on/off several times in order to expel air.
Clean the pump suction area.
Comply with specifications (8m max. head)
Use pressure line with larger diameter.
Rectify blockage.
Clean suction opening.
Straighten pressure line.
Seal pressure line, tighten threaded connections
Ensure there is sufficient liquid present.
Keep the pump at an angle while submerging.
www.sealey.co.uk
WPD235P.V2
REGISTER YOUR
PURCHASE HERE
Issue:1
01/11/22
Advertisement
