Table of Contents
Advertisement
2-11: VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V.SIZE".
4.
Press the VOL. UP/DOWN button on the remote
control until the Up/Down OVER SCAN Quantity
becomes equal to the Right/Left OVER SCAN Quantity.
2-12: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-11.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (09) on the remote control to
select "V.LIN".
4.
Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
upside and downside becomes minimum.
2-13: OSD HORIZONTAL
1.
Activate the adjustment mode display of Fig. 1-1.
2.
Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.
(Refer to Fig. 2-2)
00 OSD
A
2-14: PARABOLA CORR
1.
Receive the rainbow pattern from the Pattern Generator.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (29) on the remote control to
select "PARABOLA".
4.
Press the VOL. UP/DOWN button on the remote control
until the right and left vertical lines are straight.
ELECTRICAL ADJUSTMENTS
TV
20
B
Fig. 2-2
2-15: TRAPEZIUM
1.
Receive the rainbow pattern from the Pattern Generator.
2.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
3.
press the channel button (30) on the remote control to
select "TRAPEZIUM".
4.
Press the VOL. UP/DOWN button on the remote control
until the both vertical lines of the screen become
parallel.
2-16: CORNER CORR TOP
1.
Receive the rainbow pattern from the Pattern Generator.
2.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
3.
press the channel button (31) on the remote control to
select "COR TOP".
4.
Press the VOL. UP/DOWN button on the remote control
until the upper section of the both ends vertical lines are
straight.
2-17: CORNER CORR BOTTOM
1.
Receive the rainbow pattern from the Pattern Generator.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "COR BTM".
4.
Press the VOL. UP/DOWN button on the remote control
until the bottom section of the both ends vertical lines
are straight.
2-18: SUB BRIGHT CENTER
1.
Receive the monoscope pattern. (RF Input)
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
4.
Press the VOL. UP/DOWN button on the remote
control until the white 10% is starting to be visible
5.
Receive the monoscope pattern. (Audio Video Input)
6.
Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~4.
7.
Press the DVD button on the remote control to set to
the DVD mode.
8.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
9.
Press the VOL. UP/DOWN button on the remote
control to set the same step numbers as the AV mode.
D3-3
Advertisement
Table of Contents
