Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Outline ET Series
Summary of Contents for Outline ET Series
- Page 1 Operating Manual ET Series Electronic Turntable ET250R2-3D ET50-3D...
- Page 2 ET Series Operating Manual Version: 2.4 Release date: 2024/03/20 © Outline 2024. All rights reserved. Refer all servicing to qualified personnel, through your Outline dealer.
-
Page 3: Table Of Contents
CONTENTS System description ..................7 Unpacking ....................7 Front panel ....................8 Installation ....................9 Mounting ....................... 9 Horizontal use ....................9 Upside-down use ..................9 Vertical use ....................9 ET250R2-3D ....................10 ET50-3D ......................10 Use of mounting screws ................11 Removing the control electronics .............12 Installation precautions ...... - Page 4 NOT be disposed with other waste. It is the user’s responsibility to dispose of their electrical and electro- Conformity. All the Outline electro-acoustic and electronic devices are in conformity with the provisions of EC/EU directi- ves (as stated in our CE Declaration of...
- Page 5 Declaration of Conformity The company OUTLINE SRL, with headquarters in Via Leonardo da Vinci 56, Flero (BS), declares under its sole responsibility that all electro-acoustic and electronic audio low frequency professional products, speakers components and loudspeakers included, are manufactured in ITALY according to the below stated standards and directives (where applicable). The technical files for the products (where applicable) are compiled by Outline s.r.l.
-
Page 7: System Description
System description. Outline’s restless pursuit of perfection has resulted in rotation, which is particularly useful to loudspeaker the development of two new and improved ET Series enclosure manufacturers, for example. products, building on the unparalleled worldwide success microprocessor-based control unit... -
Page 8: Front Panel
Front panel. ET CONTROL UNIT MCU2 STEP SETTING MAINS SYNC SAVE TTL DELAY SETTING DEGREES DOWN DEGREES UP STOP ZERO STEP MAN. MAN. STEP ZERO ETHERNET ZERO SET MAINS: mains power connector. Connect stops base during rotation. using appropriate cable supplied. -
Page 9: Installation
Installation. MOUNTING The Outline ET series was designed for horizontal, vertical and upside-down use. HORIZONTAL USE The ET250R2-3D and ET50-3D have been tested to to ensure good operation of the unit and avoid it being support an axial load of 1,000 kg (2,200 lb) and 200 kg damaged. -
Page 10: Et250R2-3D
ET250R2-3D MAXIMUM LOAD Axial: 1000 kg (2200 lb) Radial: 250 kg (550 lb) Max 100 kg Bending moment (220 lb) Torque moment Max 250 kg Max 50 kg (550 lb) (110 lb) 150 cm Distance between load's centre of gravity and support surface Max 25 kg (55 lb) Max 50 kg... -
Page 11: Use Of Mounting Screws
Use of mounting screws. The Outline ET series turntables have fixing holes on the minimum value and do not exceed the specified bottom and on the platter. maximum value. The screws for the mounting holes on the top (rotating) The maximum tightening torque is 20 Nm. -
Page 12: Removing The Control Electronics
Like the previous version (Outline ET250-3D), the To make the extension cable, use the two 9-pin Combicon electronics of the new Outline ET series turntables are connectors (one male and one female) supplied with the built into the body of the mechanism. -
Page 13: Installation Precautions
Installation in excessively damp or dusty locations can cause damage to the unit or faulty operation. Mains Connection The Outline ET series turntables are fitted with a This is essential for safety and correct system operation. 3-conductor cable; the green-and-yellow wire of the mains Inside the unit, the yellow/green wire is connected to the cord must always be connected to an earth or ground. -
Page 14: Use Of The Unit With Ttl Pulse
Stand-alone use of the unit. The Outline ET series unit’s platter can rotate in both stored value is displayed; each time they are pressed directions (clockwise and counterclockwise). again raises or lowers the value by 0.5 degrees. The minimum movement step is 0.5 degrees and is made There is no absolute “zero”... -
Page 15: Use With Et Commander Software
Use with ET Commander Software. The Outline ET series turntables is supplied with dedicated software for its complete control. This software can be used to control multiple turntables, specifying the various rotation modes. Installing the software on a PC The software works on Windows operative systems it on your computer in any position (such as C:\temp, and is available from Outline’s web site (www.outline.it) -
Page 16: For Software Developers
For software developers Outline puts at the disposal of software developers a These details can be requested by sending an e-mail to DLL for the total control of the ET series turntables and info@outline.it. raw commands in case of specific control requirements. -
Page 17: Measurement Example
Measurement example. One example of 3D use of the ET250R2-3D turntables one mounted in a horizontal position and the other in a is shown in the illustrations below, intended above all vertical position. for loudspeaker enclosure manufacturers who need to This enables a 3D polar measurement to be produced in a measure their products’... -
Page 18: Technical Specifications
Technical specifications. ET250R2-3D ET50-3D ROTATION DATA Mounting Condition Horizontal, Vertical, Upside-down Horizontal, Vertical, Upside-down Drive System Irreversible worm gear Irreversible worm gear Direction Clockwise or counter-clockwise Clockwise or counter-clockwise Max speed (tolerance ±10%) 0.35 RPM 1.75 RPM Max Axial Load (only in compression) 1000 kg (2200 lb) 200 kg (440 lb) Max Axial Load (upside-down) -
Page 19: Overall Dimensions
Overall dimensions. ET250R2-3D TOP (ROTATING) BOTTOM (FIXED) 350 mm 107 mm 244 mm 455 mm ET50-3D TOP (ROTATING) BOTTOM (FIXED) 350 mm 107 mm 244 mm 455 mm... - Page 20 OUTLINE S.R.L. Via Leonardo Da Vinci, 56 - 25020 Flero (Bs) - Italy tel. +39 030 35 81 341 - www.outline.it - info@outline.it VAT IT02902720982...
Need help?
Do you have a question about the ET Series and is the answer not in the manual?
Questions and answers