EC/EU directives (as the product. stated in our CE declaration of conformity). All the Outline electroacoustic and electronic devices are in accordance with the objects stated by below CEE directives: Safety 73/23 and following modification 93/68 Art. 13 Electromagnetic compatibility 89/336 and following modification 93/68 Art.
It is advisable to keep the packaging for use in the female Combicon connector event of the unit being transported in the future. • Warranty certificate The Outline ET unit is supplied with the following • Operating manual OUTLINE S.R.L. Tel.: +39 030.3581341 www.outline.it...
MANUAL: the turntable rotates by 0.5 degrees, • Press the ESC button to exit delay modification which is the minimum movement. procedure, restoring the value already stored. OUTLINE S.R.L. Tel.: +39 030.3581341 www.outline.it Via Leonardo da Vinci, 56 Fax +39 030.3580431 25020 Flero (Brescia) Italy info@outline.it...
INSTALLATION MOUNTING The Outline ET series was designed for horizontal, vertical and upside-down use. HORIZONTAL USE The ET250R2-3D and ET50-3D have been tested support to ensure good operation of the unit and to support an axial load of 1,000 kg (2,200 lb) and avoid it being damaged.
USE OF MOUNTING SCREWS The Outline ET series turntables have fixing holes ATTENTION: DO NOT USE LONGER SCREWS: on the bottom and on the platter. THIS COULD DAMAGE OR BREAK THE UNIT� The mounting holes on the front (rotating) side...
REMOVING THE CONTROL ELECTRONICS Like the previous version (Outline ET250-3D), the electronics. electronics of the new Outline ET series turntables To make the extension cable, use the two 9-pin are built into the body of the mechanism. Combicon connectors (one male and one female) However, it is possible to separate the two supplied with the unit.
Installation in excessively damp or dusty locations can cause damage to the unit or faulty operation. MAINS CONNECTION The Outline ET series turntables are fitted with This is essential for safety and correct system a 3-conductor cable; the green-and-yellow wire operation.
STAND-ALONE USE OF THE UNIT The Outline ET series unit’s platter can rotate in value by 0.5 degrees. both directions (clockwise and counterclockwise). There is no absolute “zero” position. When the The minimum movement step is 0.5 degrees and electronics are switched on, the current position is is made by pressing the MANUAL buttons.
USE WITH ET COMMANDER SOFTWARE The Outline ET series turntables is supplied with dedicated software for its complete control. This software can be used to control up to two turntables, specifying the various rotation modes. INSTALLING THE SOFTWARE ON A PC...
“Network” FOR SOFTWARE DEVELOPERS Outline puts at the disposal of software specific control requirements. These details can be developers a DLL for the total control of the ET requested by sending an e-mail to info@outline�it�...
With a suitable mechanical structure, it is greater measurement precision. ET250R2-3D ET250R2-3D OUTLINE S.R.L. Tel.: +39 030.3581341 www.outline.it Via Leonardo da Vinci, 56 Fax +39 030.3580431 25020 Flero (Brescia) Italy...
90/250 V AC - 50/60 Hz 90/250 V AC - 50/60 Hz Room Temperature From -5° to 45° C From -5° to 45° C OUTLINE S.R.L. Tel.: +39 030.3581341 www.outline.it Via Leonardo da Vinci, 56 Fax +39 030.3580431 25020 Flero (Brescia) Italy...
OVERALL DIMENSIONS TOP (ROTATING) BOTTOM (FIXED) 350 mm 107 mm 244 mm 455 mm OUTLINE S.R.L. Tel.: +39 030.3581341 www.outline.it Via Leonardo da Vinci, 56 Fax +39 030.3580431 25020 Flero (Brescia) Italy info@outline.it...
Page 16
For this reason, any current Outline product may differ in some aspect from its description, but will always equal or exceed the original design specifications unless otherwise stated.