Advertisement
Quick Links
PN'S: 22-79HA04K, 22-79HA10K, 22-79HA16K
COMPONENTS: - Note: Each kit comes with one HFS and one H
1. H
F
YDRA
USION
lbs. (9072 kg) shoring capacity with 4:1 Safety Factor. Size dependent on stroke length. For use
with Paratech LongShore, AcmeThread and LockStroke struts.
.
PN 22-79HA04 - 4" (10.2 cm) stroke HFS. Component weight, 18.7 lbs. (8.5 kg).
PN 22-79HA10 - 10" (25.4 cm) stroke HFS. Component weight, 28.3 lbs. (12.8 kg).
PN 22-79HA16 - 15.9" (40.4 cm) stroke HFS. Component weight, 37.2 lbs. (16.9 kg).
2. H
F
YDRA
USION
(3.05 m) non-conductive hose, no-spill coupler, pump base and pressure gauge. Rated for
10,000 psi (689.5 bar). Assembly weight, 24.20 lbs (10.98 kg).
FIGURE-1
Paratech Incorporated
P.O. Box 1000, Frankfort, IL 60423 USA
Customer Service: 800.435.9358
Phone: 815.469.3911 Fax: 815.469.7748
E-mail: paratech@paratech.com
INSTRUCTION SHEET
H
F
YDRA
USION
STRUTS: 10 ton (9.1 metric ton) lift capacity with 2:1 Safety Factor and 20,000
PUMP, PN 22-790020G: Two stage, single acting, hydraulic pump with 10 foot
Paratech Europe, Branch of Paratech Inc.
P.O. Box 174, 5260 Odense S, Denmark
Email: paratech@paratech.dk
STRUT (HFS) KIT
F
YDRA
USION
Pump. See FIGURE-1
Advertisement
Related Manuals for paratech 22-79HA04K
Summary of Contents for paratech 22-79HA04K
- Page 1 USION lbs. (9072 kg) shoring capacity with 4:1 Safety Factor. Size dependent on stroke length. For use with Paratech LongShore, AcmeThread and LockStroke struts. PN 22-79HA04 - 4” (10.2 cm) stroke HFS. Component weight, 18.7 lbs. (8.5 kg). PN 22-79HA10 - 10” (25.4 cm) stroke HFS. Component weight, 28.3 lbs. (12.8 kg).
- Page 2 Component weight, .4 lbs. (.2 kg). 2. Strut Converter, PN 22-796035: Used in the HFS Dual Shaft End Adapter with any compatible Paratech base. Component weight, 2.7 lbs. (1.2 kg). 3. 10’ Hose extension w/No-Spill Couplers, PN 22-790030X: Used with HFS PUMP, component weight, 2.21 lbs (1 kg).
-
Page 3: Basic Safety Precautions
HFS AND PUMP OPERATION: 1. Couple the HFS tube end down onto any compatible Paratech base plate and make sure the LockPin is secure. Note: The HFS can be used in any orientation; however, tube end down is preferred to facilitate LockCollar adjustment and eliminate trip hazards by keeping the hydraulic hose at ground level. - Page 4 The Dual End Shaft Adapter was engineered to accept Paratech LongShore, AcmeThread, or LockStroke products.** Do not insert strut screw ends into the Dual Shaft End Adapter. Bases can be used on the Dual End Shaft Adapter with a Paratech Extension Convert- er, PN 22-796035. See FIGURE-5.
- Page 5 Push the no-spill couplers together until they lock and then turn the locking collar to prevent accidental disconnection. See FIGURE-7 FIGURE-7 6. To unlock the pump handle, push handle down then slide yoke off handle grip. This places the handle in an open or working position. To lock the handle, push the handle down and push yoke onto the handle grip.
- Page 6 8. To release pressure, open the pump control lever by SLOWLY turning CCW to control the load descent. 9. As the load is lifted, the LockCollar should be turned down to make contact with the HFS tube body, shoring the load. See FIGURE 10. Note: maximum lift height is slightly more than maxi- mum stabilizing height to prevent system lockout in application.
- Page 8 NOTE: USING THE SCREW SIDE IN THE HFS DUAL SHAFT END ADAPTER WITHOUT LONGSHORE SCREW APDAPTER PN 790019 OR ACMETHREAD SCREW ADAPTER PN 790067 WILL RESULT IN 10% LOWER CAPABILITY. FIGURE 12 FIGURE 13...
-
Page 9: Tool Maintenance
The HFS should be fully retracted before checking the fluid level in the pump. Replen- ish fluid levels with Paratech hydraulic fluid PN 22-790051. Apply grade 10 motor oil or grease to all pivot and rubbing points on the pump regularly. - Page 12 Each HFS or component thereof, manufactured by Paratech Incorporated, has been thoroughly inspected and properly adjusted before shipment to insure the highest quality and the greatest possible reliability. Paratech Incorporated (hereinafter referred to "Seller') hereby warrants the HFS or component...