Table of Contents
Advertisement
Quick Links
C
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when handling
AUTION
this equipment.
1.0 INSTALLATION
1.1 Unpack and Inspect the Equipment
The following components should be included:
1 UIM-2E1
4 #6 Phillips Panhead Nylon Locking Screws
2 #6 Phillips Beige Flathead Screws
If there is any visible damage, do not attempt to connect the device. Contact Customer Support at 1-877-
638-2638 (1-603-427-0600 for international customers) or
1.2 Configure the E1 Ports
The E1 Configuration Switches for both Port 1 and Port 2 are on the component side of the UIM-2E1 circuit
board, opposite the faceplate/label. When facing the Configuration Switches, Port 1 switches are on the
left and Port 2 switches are on the right. Switches for both ports are numbered from left to right, #1-8.
N
Port 2 Configuration Switches on the UIM-2E1 are NOT USED: frame type and line code for Port 2 are determined by
OTE
the Port 1 switch settings. BOTH ports determine speed and timing configurations via communication with the remote
E1 equipment to which the UIM-2E1 is connected.
Switch # Configuration Switch # Configuration
1
not used
2
not used
3
FRAME TYPE
4
LINE CODE
1.2.1 Frame Type
Frame type is the data encapsulation method. An E1 frame consists of 248 data bits (an 8-bit
sample of each of the 31 E1 data channels), plus 8 synchronization bits, transmitted at a rate of
8,000 frames per second across the E1 line.
220-0000083 rev 01
UIM-2E1
E1 Loop Bonding Uplink Interface Module
PORT 1 SWITCHES
5
not used
6
not used
7
not used
8
not used
Installation Instructions
support@nettonet.com
.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Net to Net Technologies UIM-2E1
Summary of Contents for Net to Net Technologies UIM-2E1
-
Page 1: Installation Instructions
Port 2 switches are on the right. Switches for both ports are numbered from left to right, #1-8. Port 2 Configuration Switches on the UIM-2E1 are NOT USED: frame type and line code for Port 2 are determined by the Port 1 switch settings. - Page 2 1.3.1.1 Affix the UIM-2E1 to a MUM The UIM-2E1 can be installed on a MUM that is already in service, though you must remove the MUM from the IP DSLAM chassis in order to do so. Removal of a MUM from a powered IP DSLAM will not affect the operational status of other modules within the chassis;...
- Page 3 Remove the (8) beige flathead screws securing the Mini DSLAM chasis and carefully lift off the chassis cover. Set the screws aside. Select a port on the Mini DSLAM for UIM-2E1 installation: either port (1 or 2) may be used. Although not required for operational purposes, if redundancy is desired two UIMs may be installed on a Mini DSLAM, one in each port.
- Page 4 Plug the E1 cable into one of the two E1 RJ45 ports on the UIM-2E1 faceplate; either port (1 or 2) may be used. Verify the connection: the E1 Lnk LED on the UIM-2E1 faceplate (Port 1 Lnk or Port 2 Lnk depending upon which port was connected) will flash green to indicate the connection is established and operational.
-
Page 5: Additional Information
(A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid, less constant rate.) 3.2 European Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to the UIM-2E1 as installed in a Mini DSLAM or on a MUM in an IP DSLAM. 220-0000083 rev 01... - Page 6 This Class A product complies with European Norm EN55022. Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct the situation. 220-0000083 rev01 © Copyright 2002 Net to Net Technologies, Inc. ™...
Need help?
Do you have a question about the UIM-2E1 and is the answer not in the manual?
Questions and answers