Singer momento User Manual

Singer momento User Manual

Craft cutting machine
Hide thumbs Also See for momento:

Advertisement

User Guide
Craft Cutting Machine

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the momento and is the answer not in the manual?

Questions and answers

susan Trainer
February 10, 2025

How? to import a svg file from silhouette to singer moments and cut it out

1 comments:
Mr. Anderson
May 14, 2025

To import an SVG file from Silhouette to the Singer Momento and cut it out, follow these steps:

1. Export the design from Silhouette software as an SVG file.
2. Open the mySewnet software, required for the Singer Momento.
3. Import the SVG file into mySewnet.
4. Save the imported file if necessary.
5. Send the file to the Singer Momento for cutting.

Make sure the SVG file is properly traced and saved before importing.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Singer momento

  • Page 1 User Guide Craft Cutting Machine...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this product. Keep the instructions at a suitable place close to the machine. Make sure to hand them over if the machine is given to a third party.
  • Page 3 • Do not use bent cutting blades. • Do not use the machine if it is wet. • Wear safety glasses. • Please do not touch the mat or material during the cutting process, even if the • Switch the machine off (“0”) when mat or material has stopped moving.
  • Page 4: Federal Communication Commission Interference Statement

    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the authorized SINGER® retailer or an experienced radio/TV technician for help. The included interface cable should be used in order to ensure compliance with the limits for a Class B digital device.
  • Page 5 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada.
  • Page 6: Intended Use

    The optimal uses are described in these instructions. This product is not intended for industrial or commercial use Additional assistance, by region, may be found online at www.singer.com. You can find a digital version of this manual online at singer.com/momento Machine Overview – Front 1. Tablet / Phone Holder 7.
  • Page 7: Overview Accessories

    3. Basic Blade In Housing 4. Rotary Blade 5. The Basic Blade 6. Pen 7. Pen Adapter 8. 12”X 24” Mat Optional Accessories Additional optional accessories are available for your machine. Check with your au- thorized SINGER® retailer or singer.com for more information.
  • Page 8 Layflat Door – Front Flap Gently pull down on the front flap to open the door. The door is designed to open and fold down smoothly, with a damping mechanism for smooth, effort- less opening. Once the front door is open, it should rest flat on the surface and be flush with the cutting area.
  • Page 9: Setting Up Machine

    Setting Up Machine 1. Place your machine on a sturdy, horizontal surface. Make sure there is enough room both in front and behind the machine for the material to move in and out of the machine while cut- ting. 2. Connect the power adapter to the machine and then plug it into a wall outlet.
  • Page 10: Lcd Screen

    MySewnet Crafting Software To get started and unleash the full power of your SSinger Momento Craft Cutting Machine, visit the mySewnet website at www.mysewnet.com to download the mySewnet Crafting software. The software provides guidance and tu- torials for both beginners and advanced crafters alike.
  • Page 11: Lcd Screen: Settings

    LCD Screen: Settings 1. Wifi 2. Language 3. Camera 4. Screen Brightness 5. Unit Settings 6. About...
  • Page 12 Connecting the Machine to Computer Via USB To operate your machine, ensure that it is connected to a power source and that it is turned on. The machine can be connect- ed either via USB or Wi-Fi. If both options are available, it is recommended to use Wi-Fi as the primary connection method.
  • Page 13 Connecting the Machine to Computer Via WIFI To begin the onboarding process for your machine, simply power it on. Connecting to WiFi is an essential step in this pro- cess. When prompted, follow the instruc- tions displayed on the screen to set up your WiFi connection.
  • Page 14 To find instruc- tions on replacing additional blades, visit Singer.com.
  • Page 15 Installing Cutting Blade On Machine 1. Pull the locking mechanism out. 2. Insert the cutting blade into the right slot (A). 3. While the locking mechanism is pulled out, ensure that the grooves on the blade line up with the groove on the mechanism.
  • Page 16 Installing Rotary Blade 1. Insert the blade into the right slot. 2. Pull the locking mechanism out. 3. While pulling out the locking mech- anism, make sure that the grooves on the blade align with the groove on the mechanism. The rotary blades have teeth on the top that should insert into corresponding holes on the top of the carriage...
  • Page 17: Pinch Wheels

    Pinch Wheels 1. Locate the pinch wheel lever at the back-right side of the machine. 2. To raise the pinch wheels, pull down the lever. To lower the pinch wheels, release the lever. Lift the lever up to unlock and down to lock. 3.
  • Page 18 How to load the mat You can load the mat anytime during your The mat will feed in and out automatically project process before cutting. and stop with the top of the mat under the rollers, and the top of the material 1.
  • Page 19: Starting A Cut

    Starting a Cut This instruction will walk you through the steps to start a cut on the machine effectively. Whether you prefer to choose a preset design or send a design from the software - we’ve got you covered. Let’s get started! 1.
  • Page 20 Matless cutting - only for selected materials Matless cutting, provides a convenient 5. The material will feed in and out until and efficient option for specific materi- it reaches the starting position where als such as vinyl and adhesive-backed it is under the rollers. materials like sticker paper.
  • Page 21 Camera Calibration Guide for Left Pen Camera calibration is an essential pro- 9. Position the Red + Symbol: cess to ensure precise positioning and 10. After the drawing is completed, touch accurate results when using the left pen the middle position of the + symbol on on your machine.
  • Page 22 Camera Calibration Guide for Right Tool Holder Before you begin the calibration, make 9. After the drawing is completed, touch sure to gather the following items: the middle position of the + symbol on the captured image displayed on the Items Needed for Calibration: screen.
  • Page 24 SINGER and the Cameo “S” Design are exclusive trademarks of The Singer Company Limited S.à.r.l. or its Affiliates. CONTOUR is an exclusive trademark of Singer Sourcing Limited LLC or its Affiliates. © 2023 The Singer Company Limited S.à.r.l. or its Affiliates. All rights reserved.
  • Page 25 MANUFACTURER VSM Group AB, SVP WORLDWIDE Soldattorpsgatan 3, SE-55474 Jönköping, SWEDEN...
  • Page 26 Reshape your crafting experience. 471xxxxxxA • English • ©2023 The Singer Company Limited S.à.r.l. or its Affiliates. • All rights reserved.

Table of Contents

Save PDF