Advertisement
Quick Links
Advertisement
Summary of Contents for QANBA 2009 ARCADE
- Page 1 Installation manual Arcade...
- Page 3 Control console packing box material list Console x 1，Floor Protector Mat x 2 Please open both boxes and check the quantity of all items Console Joystick guard Storage baskets Floor protector (on console) （x2） mat（x4）...
- Page 4 List of materials prepared before installation Installation preparation: Console * Please read the installation manual carefully Joystick guard (on console) Console...
- Page 5 Accessory box：Phillips screwdriver x 1，6x30mm Screw x 4， 6-inch cable ties x 12，10-inch cable ties x 25， USB cable x 4（Reserve on demand） 6x30mm Phillips screwdriver screw（x 4） 6-inch cable ties（x 12） 10-inch cable ties（x 25） USB cable（x 4）...
- Page 6 Step 1: Install console components Note: When installing the console, tilt it in. You can't just push it in.
- Page 7 Note: Align both sides when installing, do not shift the center...
- Page 8 Step 2: Secure the console using a Phillips screwdriver (O) and four 6x30mm screws (Q) Clockwise tightening...
- Page 9 Internal cable installation Step 1: Open the console panel by unscrewing the three pin hand screws (P) at the bottom of the console. Unscrew counterclockwise...
- Page 10 Step 2: Open the panel from the console and use a phillips screwdriver (O) to remove the M4 screw (R) that locks the motherboard area in the console. Unscrew counterclockwise...
- Page 11 Step 3: Open the mainboard area and insert the USB port of the USB cable (N) through the square hole at the bottom of the console. *After reserving sufficient length of the USB cable, you can use a 6-inch cable tie (L) or 10-inch cable tie (M) to arrange the cable.
- Page 12 Step 4: Cover the motherboard area panel and reinstall it with the M4 screw (R) you just removed. And cover the console panel. Clockwise tightening...
- Page 13 Step 5: Reinstall and tighten the three plum hand screws at the bottom of the console. Clockwise tightening...
- Page 14 Display connection and installation Depending on your needs, you can place the monitor on the platform, or use a third- party monitor holder (30mm thickness on the back of the table) to install it.
- Page 15 Use a 6-inch cable tie (L) or a 10-inch cable tie (M) to arrange the wire as needed. Note: This product does not contain monitor and monitor stand, please install according to the actual situation.
- Page 16 Characteristics Compatible button Function button...
- Page 17 Compatible button A LS button Compatible button B RS button Compatible button C CLICK button Compatible button D Joystick mode switch Tournament mode switch Directional joystick HOME button Common button area SELECT button START button Turbo function button...
- Page 18 Product operation instructions USB output mode sliding switch 1. Flip the S1 switch on the mainboard to select the mode of connecting multiple devices through four USB cables (N), or connecting to devices through only one USB cable. When the S1 switch slides to the left, multiple device controls are connected via 4 USB cables (N);...
- Page 19 2. In the default mode, after connecting to different devices, you need to press the compatibility button to achieve the function of switching device compatibility.
- Page 20 3. When multiple devices are connected using four USB cables (N), the A(1)/B(2)/C(3)/D(4) mode button is used to switch the compatibility mode. You do not need to insert or remove the USB cables of different devices.
- Page 21 Tournament mode 1. Tournament mode switch (5) When unlocking (default), compatible buttons A/B/C.D and function buttons HOME/SELECT/TURBO can be used normally. 2. When the Tournament mode switch (5) is locked, the compatible button A/B/C.D and the function button HOME/SELECT/TURBO are unavailable.
- Page 22 Joystick mode The directional joystick (13) can slide the switch (12) through joystick mode, Switch between the following three modes DP: Directional pad LS: Left stick RS: Right stick * Some games can only use LS control mode.
- Page 23 Turbo Function Common key area (14) Each button can be switched and cycled between the following three continuous transmission modes Repeated message mode: ① Continuous transmission off (default) - LED light off state; ② Press a button in the common key area (14), and at the same time, press the serial function button (8) to open the serial function of the button.