Subscribe to Our Youtube Channel
Related Manuals for alkitronic X H Series
Summary of Contents for alkitronic X H Series
- Page 1 X Driver Systems Operating and Maintenance Manual Hydraulic torque wrench X Driver System...
-
Page 2: Table Of Contents
3.3.2 Correct / incorrect A-Drive supports ing staff prior to commissioning or maintenance. They 3.3.3 Positioning DMA extensions must be constantly kept at the place where the alkitronic® Norwolf hydraulic torque wrenches will be used. Operation This operating and maintenance manual refer exclusively Connecting hydraulic hoses to the alkitronic®... -
Page 3: A Receiving Inspection / Packaging
195 mm. Small housing radius and with patented latch lock. Extremely flat design with flush mounting. The hydraulic alkitronIC® Norwolf 2-hose system hydraulic wrenches are used to tighten or loosen heavy bolted con- Model V-Drive of 260 Nm up to approx. 62,300 Nm * for nections. -
Page 4: Technical Specifications
If you have questions about safety measures and application areas, alki STACO (Nut) STABI (Connector) TECHNIK GmbH or your alkitronic® partner will be happy to assist you. Improper operation, improper use, misuse or op- eration by unqualified personnel can cause serious personal injury and property damage. -
Page 5: Operation
Operation The alkitronic® Norwolf hydraulic wrench may only be used if the technical data (See the torque table) matches the pressure settings on the hydraulic unit. The alkitronic® Norwolf hydraulic wrench and the hydraulic unit must be grounded to prevent poten- tial electric shocks. -
Page 6: Preparation For Application Model V-Drive
After changing over, check inserts and adapters for a tight fit, otherwise injury to property or people may occur. Proper positioning of the alkitronic® DMA, see page 7, point 3.2.4 3.2.3 Equiped with output inserts Example alkitronic® STACO (Standard Nut) First, prepare the wrench for the desired direction of rotation (tightening or loosening) (Fig. -
Page 7: Support Area Model V-Drive
The ball lock must engage so that the square is thus secured. See also Fig. 3 and Fig. 4. Then push the alkitronic® STACO (2) onto the square (see picture below). Insert locking pin and secure with rubber ring. -
Page 8: Preparation For Application Model A-Drive
Power head (1) Fig. 8 - Examples of correct / incorrect support modes alkitronic® STA (5) To reduce the wrench size an alkitronic® STA (5) can optionally be inserted into the hexagonal drive (accessory). Selection of the direction of rotation (tightening / loos-... -
Page 9: Positioning Dma Extensions
DMA with the A-Drive Return (R) housing in a form fitting manner. Do not lift or carry the alkitronic® Norwolf hydraulic wrench by the couplings or hoses. Connecting Avoid kinked hoses or using hoses with too small of bolt (5) a bend radius to ensure proper and safe operation. -
Page 10: Tightening And Loosening Of Bolts
For individual solutions your 4.2.2 Commissioning of the hydraulic power unit alkitronic® partner will be happy to help. Measures during initial setup or startup Always fit output inserts such as STA / STACO etc. -
Page 11: Description Tightening / Releasing
After the piston is fully extended, release the button. The wrench is thus prevented. piston will move back automatically and you will hear 1-3 • Do not carry the alkitronic® Norwolf hydraulic wrench by "click” sounds. the hoses or couplings. -
Page 12: Check Tightness And Impurities
• Check the condition of the wrench, high-pressure hoses alkitronic® Norwolf hydraulic wrenches should and connections. be dried and cleaned then stored in an alkitronic® • Eliminate damage and dirt. case or another lockable container. Moisture leads • Dirt particles in the hydraulic system can cause malfunc- to oxidation on the housing, output as well as on tions and breakdowns. -
Page 13: Lubrication Points / Parts Maintenance
NORWOLF Hydraulic Torque Wrench System Torsional Lubricating points X-Driver connector (without dismantling housing) Power head Check connections Locking X-Driver Spring and pin Tighten in the screw, the release latch Clean side surfaces now has no function Bolt Drive lever Spring/pin A-Drive Housing Release... -
Page 14: Troubleshooting
(see page 7, section 3.2.4 / page 8, 3.3.1 - Reaction torque transducer). Get in contact with your alkitronic® Partner to see if an application spe- cific support or a more suitable alkitronic® Norwolf hydraulic wrench... -
Page 15: Technical Data
NORWOLF Hydraulic Torque Wrench System Technical Data Model A-Drive Model V-Drive Reaction Arm Models A-Drive (hexagonal drive) Type A-Drive + X-Driver A - 2 A - 4 A - 8 A - 16 A - 32 A - 64 Torque range * 335-2240 805-5370 1560-10400... - Page 16 Spare part and repair service alki TECHNIK GmbH Development, Production and Distribution of Bolting Systems Unterlettenweg 4 – 85051 Ingolstadt/Germany – fon +49 841 97499-0 – fax +49 841 97499-90 info@alkitronic.com – www.alkitronic.com EXTRACT FROM OUR PRODUCT RANGE THE ELECTRICS THE PNEUMATICS...
Need help?
Do you have a question about the X H Series and is the answer not in the manual?
Questions and answers