Summary of Contents for Allied Data Technologies CopperJet 810
Page 1
CJT 81x 02-10-2001 11:45 Pagina 1 Installation Manual CopperJet 81x ADSL Modem series Allied Data CopperJet 81x = 810, 811, 812 & 813 T E C H N O L O G I E S...
CJT 81x 02-10-2001 11:45 Pagina 2 CopperJet 81x Contents Packaging contents...3 Ethernet Installation Guide...4 Installing the CopperJet 81x Configurator...5 USB Installation for Windows 98 SE ...9 USB Installation for Windows ME..13 USB installation for Windows 2000...17 Using the ADSL CopperJet 81x Configurator...22 Configuring RFC1483 Bridged ...23 Configuring RFC1483 Routed ...25 Configuring PPPoA ...27...
To prevent overheating, make sure enough free space is available on both sides, and above the CopperJet 81x to permit free airflow. Production Name: Line CJ8M0 E/U PSTN CJ8M0 E/U ISDN ISDN CopperJet 810 PSTN CopperJet 811 ISDN CopperJet 812 PSTN CopperJet 813 ISDN Advice: Set for the Copperjet 81x with firmware version 4.17 or higher the Line Modulation on...
CJT 81x 02-10-2001 11:45 Pagina 4 CopperJet 81x Ethernet Installation Guide Note: You must have installed an Ethernet 10Base-T card in your computer first. Installation when you already have a LAN connection. 1. Connect your CopperJet 81x with the Ethernet straight cable to your Ethernet Hub. 2.
CJT 81x 02-10-2001 11:45 Installing the CopperJet 81x Configurator. After installing the CopperJet configurator you be able to configure the CopperJet 81x. During installation you can choose the setup you prefer, Typical this will install the most common options. Compact this will install only the CopperJet configurator. Custom you may choose the options you want to install.
Page 6
CJT 81x 02-10-2001 11:45 Pagina 6 CopperJet 81x 3. Click on Next. 4. Click on Next. 5. Click on Next. Allied Data Technologies...
Page 7
CJT 81x 02-10-2001 11:45 Pagina 7 CopperJet 81x 6. Click on Next. 7. Click on Next. 8. Click on Next. Allied Data Technologies...
Page 8
CJT 81x 02-10-2001 11:45 Pagina 8 CopperJet 81x 9. Click on Finish. 10. The CopperJet configurator is now installed. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 Pagina 9 CopperJet 81x USB Installation for Windows 98 SE. During the installation you need the official Windows 98 SE CD-ROM. A: Place the CD-ROM provided in the CD-ROM drive. B: Connect your power adapter to the power outlet and into the Copperjet 81x. C: Connect your USB cable into your Copperjet 81x and your computer.
Page 10
CJT 81x 02-10-2001 11:45 CopperJet 81x 3. Specify a location, D:\CJT_810_EU\USBdrivers and click on Next. 4. Click on Next. 5. Click on Finish. Pagina 10 Allied Data Technologies...
Page 11
CJT 81x 02-10-2001 11:45 Pagina 11 CopperJet 81x 6. Click on Next. 7. Click on Next. 8. Click on Next. Allied Data Technologies...
Page 12
CJT 81x 02-10-2001 11:45 Pagina 12 CopperJet 81x 9. Click on Next. 10. Click on OK. 11. Click on Finish. 12. Click on Yes. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 USB Installation for Windows ME. A: Place the CD-ROM provided in the CD-ROM drive. B: Connect your power adapter to the power outlet and into the Copperjet 81x. C: Connect your USB cable into your Copperjet 81x and your computer. D: Connect your RJ11 cable to your CopperJet 81x and into the phone outlet.
Page 14
CJT 81x 02-10-2001 11:45 Pagina 14 CopperJet 81x 3. Click on Next. 4. Click on Finish. 5. Specify the location of the driver, and click on Next. Allied Data Technologies...
Page 15
CJT 81x 02-10-2001 11:45 6. Specify a location, D:\CJT_810_EU\USBdrivers, and click on Next. 7. Click on Next. 8. Click on Next. Pagina 15 CopperJet 81x Allied Data Technologies...
Page 16
CJT 81x 02-10-2001 11:45 Pagina 16 CopperJet 81x 9. Click on Finish. 10. Click on Yes. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 Pagina 17 CopperJet 81x USB installation for Windows 2000. A: Place the CD-ROM provided in the CD-ROM drive. B: Connect your power adapter to the power outlet and into the Copperjet 81x. C: Connect your USB cable into your Copperjet 81x and your computer. D: Connect your RJ11 cable to your CopperJet 81x and into the phone outlet.
Page 18
CJT 81x 02-10-2001 11:45 CopperJet 81x 3. Specify a location and click on Next. 4. Copy manufacturer’s files from, D:\CJT_810_EU\USBdrivers, and click on OK. 5. Click on Next. Pagina 18 Allied Data Technologies...
Page 19
CJT 81x 02-10-2001 11:45 Pagina 19 CopperJet 81x 6. Click on Finish. 7. Click on Next. Search for a suitable driver for my device, and click on Next. Allied Data Technologies...
Page 20
CJT 81x 02-10-2001 11:45 CopperJet 81x 9. Specify a location and click on Next. 10. Copy manufacturer’s files from, D:\CJT_810_EU\USBdrivers, and click on OK. 11. Click on Next. Pagina 20 Allied Data Technologies...
Page 21
CJT 81x 02-10-2001 11:45 Pagina 21 CopperJet 81x 12. Click on Yes. 13. Click on Finish. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 CopperJet 81x Using the ADSL CopperJet 81x Configurator. This configuration tool is needed to create profiles for the Copperjet 81x. Profiles can be stored for later use or can be uploaded directly to the Copperjet 81x. You can also use the configurator when a profile has been provided by your Service Provider.(You can go directly to the Upload section).
CJT 81x 02-10-2001 11:45 Configuring RFC1483 Bridged. 1. Select RFC1483 Bridged as profile type and click on OK. 2. Set the TCP/IP parameters. Optional: an IP Address and Subnetmask is only needed for further management use. Select the Line modulation. (ADSL connection Protocol) -Multimode : Modem will detect the Modulation...
Page 24
CJT 81x 02-10-2001 11:45 CopperJet 81x Set Filter Table age, this is the time in seconds the device needs to store the MAC-addresses. Encapsulation. -LLC : Logical Link Control -VcMux : Null Encapsulation DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP-Address will be the CopperJet 81x IP address.(Not needed by Bridged) Click on OK when finished, the profile will be stored in My Documents.
CJT 81x 02-10-2001 11:45 Configuring RFC1483 Routed. 1. Select RFC1483 Routed as profile type and click on OK. 2. Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address) Set the interface type. USB when the CopperJet 81x is connected with a USB cable. Ethernet when the CopperJet 81x is connected with a Ethernet cable.
Page 26
CJT 81x 02-10-2001 11:45 Pagina 26 CopperJet 81x You must set NAT when de LAN IP-Address differs from the WAN IP-Address. Set Routing default gateway if needed.(CopperJet 81x WAN IP-Address) DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP Address will be the CopperJet 81x IP address.
CJT 81x 02-10-2001 11:45 Configuring PPPoA. 1. Select PPPoA as profile type and click on OK. 2. Set Authentication. Fill in your Username and Password. Choose the Authentication Protocol.(PAP or CHAP) Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address) The Default Gateway of your local network will be the CopperJet 81x IP-Address Set the interface type.
Page 28
CJT 81x 02-10-2001 11:45 Pagina 28 CopperJet 81x Set NAT (Network Address Translation) if needed. You must set NAT when de LAN IP-Address differs from the WAN IP-Address. DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP-Address will be the CopperJet 81x IP address.
CJT 81x 02-10-2001 11:45 Configuring PPPoE. 1. Select PPPoE as profile type and click on OK. 2. Set Authentication. Fill in your Username and Password. Choose the Authentication Protocol.(PAP or CHAP) Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address). The Default Gateway of your local network will be the CopperJet 81x IP-Address Set the interface type.
Page 30
CJT 81x 02-10-2001 11:45 Pagina 30 CopperJet 81x Set NAT (Network Address Translation) if needed. You must set NAT when de LAN IP-Address differs from the WAN IP-Address. DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP-Address will be the CopperJet 81x IP address.
CJT 81x 02-10-2001 11:45 Configuring PPTP. 1. Select PPTP as profile type and click on OK. 2. Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address). The Default Gateway of your local network will be the CopperJet 81x IP-Address Set the interface type. USB when the CopperJet 81x is connected with a USB cable.
Page 32
CJT 81x 02-10-2001 11:45 Pagina 32 CopperJet 81x Click on OK when finished, the profile will be stored in My Documents. The profile can be uploaded to the Copperjet 81x as described in the upload section. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 Configuring IPoA. 1. Select IPoA as profile type and click on OK. 2. Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address) Set the interface type. USB when the CopperJet 81x is connected with a USB cable. Ethernet when the CopperJet 81x is connected with a Ethernet cable.
Page 34
CJT 81x 02-10-2001 11:45 Pagina 34 CopperJet 81x Set Routing default gateway if needed.(CopperJet 81x WAN IP-Address) DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP Address will be the CopperJet 81x IP address. Set the DHCP server when needed.
CJT 81x 02-10-2001 11:45 Pagina 35 CopperJet 81x Configuring the DHCP Server. This is a example how to configure the DHCP Server. 1. Select DHCP Server, and click on Configuration. 2. Click on Add. Allied Data Technologies...
Page 36
CJT 81x 02-10-2001 11:45 CopperJet 81x 3. Fill in your Subnet and Netmask. The Subnet must be in the same network as your CopperJet 81x IP Address, and click on OK. 4. Fill in the range of IP Addresses you want to use, and click on Add. Note: Do not use the CopperJet 81x IP Address in your IP range.
Page 37
CJT 81x 02-10-2001 11:45 6. Fill in the Routers IP Address, this is the CopperJet 81x IP Address, and click on Add. 7. Click on OK. 8. Click on OK when finished, the profile will be stored in My Documents. The profile can be uploaded to the CopperJet 81x as described in the upload section.
CJT 81x 02-10-2001 11:45 CopperJet 81x Uploading the profile into the CopperJet 81x. With the CopperJet configurator you can upload your profile into your CopperJet 81x. 1. Start the CopperJet Configurator. 2. Click on the MAC address, and click on Upload profile. 3.
Page 39
CJT 81x 02-10-2001 11:45 4. Click on Start. 5. Wait till the CopperJet 81x has rebooted, and click on Exit. Note: Additional LAN Network settings maybe needed. Pagina 39 CopperJet 81x Allied Data Technologies...
CJT 81x 02-10-2001 11:45 CopperJet 81x Retrieving the profile from your CopperJet 81x. With the CopperJet configurator you will be able to retrieve your profile from your CopperJet 81x. 1. Start the CopperJet Configurator. 2. Click on the MAC address, and click on Get profile.
Page 41
CJT 81x 02-10-2001 11:45 Pagina 41 CopperJet 81x 5. Your saved profile is now stored in My Documents. Allied Data Technologies...
CJT 81x 02-10-2001 11:45 CopperJet 81x Updating the firmware in the CopperJet 81x. With the CopperJet configurator you can upload a new firmware into your CopperJet 81x. New firmware will be available on our website. Note: Don’t disconnect the power suply, USB cable or Ethernet cable during the upload. 1.
Page 43
CJT 81x 02-10-2001 11:45 4. Click on Start. 5. Click on Exit. 6. Click on Refresh, the CopperJet 81x MAC address and new firware version will be shown. Pagina 43 CopperJet 81x Allied Data Technologies...
CJT 81x 02-10-2001 11:45 CopperJet 81x Troubleshooting guide. This section may help when you may find some problems with the product. Please check our website: www.allieddata.com for updates on manuals, drivers and firmware. General Power-LED is not burning: - Check if your power adapter is connected to your ADSL modem and the power network ADSL-LED is not burning: Your ADSL modem doesn’t see the Central Office Equipment.
Page 45
CJT 81x 02-10-2001 11:45 ADSL Profile Configurator or Loader doesn’t detect an ADSL modem in your network - Check if the modem is in the same physical LAN as the configuring PC - Check if the modem’s IP address is in the same IP-subnet as the configuring PC. This IP-address can be found in the downloaded profile using the ADSL Profile Configurator.
CJT 81x 02-10-2001 11:45 Pagina 46 CopperJet 81x Glossary ADSL Strictly speaking, Asymmetric Digital Subscriber Line defines only a way of transmitting broadband data (at speeds between 64kbps and 8Mbps) between a user’s premises (home or office) and the local telephone exchange. In order to increase the number of customers that it is possible to serve, the upstream speed (from the user) is lower than the downstream speed (to the user), so the service is ‘asymmetric’.
Page 47
CJT 81x 02-10-2001 11:45 Authentication will normally be performed by the BAS, probably by reference to a RADIUS server. The Broadband Access Server could be described as a highly flexible and configurable ATM/PPP/IP switch/router. The function of the BAS is to ‘unwrap’ any encapsulation used to carry the TCP/IP traffic over the ATM connection and pass the data into the ISPs normal network.
Page 48
CJT 81x 02-10-2001 11:45 CopperJet 81x Note that ‘RFC 1483’ by itself doesn’t tell you what the protocol is - you need to know if the connection is bridged or routed to know what ‘RFC 1483’ means. DSLAM The unit in the telco’s local exchange that houses the ADSL modems and consolidates all the data connections onto a single ATM fibre connection, typically at 155Mbps currently.
Page 49
CJT 81x 02-10-2001 11:45 Pagina 49 CopperJet 81x So, you place each document into its own ‘internal’ envelope before placing all the ‘internal’ envelopes inside the big one. Another, more appropriate analogy: An ISP may specify that all TCP/IP messages must be placed inside a brown envelope marked ‘PPP’...
Page 50
CJT 81x 02-10-2001 11:45 CopperJet 81x G.dmt = G.992.1, derived from T1.413; also known as ‘Full rate’ This is the type of ADSL most commonly implemented now. IP over LLC/SNAP This is a routed connection method and is one of the options of RFC 1483. Note that ‘RFC 1483’...
Page 51
CJT 81x 02-10-2001 11:45 Pagina 51 CopperJet 81x Showtime Jargon for the ADSL state (that may be signalled by a green ‘line’ LED being permanently on rather than flashing) equivalent to the ‘CD’ LED or ‘CONNECT’ message from a modem. May mean (if you’re unlucky and the line is bad) that you have a 32kbps connection to the DSLAM in your local exchange, since this is normally the ‘minimum’...
Manufacturer’s Name: Manufacturer’s Address: declares that the product: Product Name: CopperJet 810 Conforms to the following standard(s) or other normative document(s): EMC: EN 55022 Class A (1994) Limits and methods of measurement of radio disturbance characteristics of information technology equipment.
Page 53
RENs, contact the local telephone company. If trouble is experienced with this equipment CopperJet 810, for repair or warranty information, please contact Allied Data Technologies +1 (614) 7774232. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Page 54
CJT 81x 02-10-2001 11:45 CopperJet 81x Declaration of Conformity Manufacturer’s Name: Manufacturer’s Address: declares that the product: Product Name: CopperJet 811 Conforms to the following standard(s) or other normative document(s): Safety: EN 60950 (1992/93) Safety of information technology equipment, including electrical business equipment. UL (IEC950) Statement that the equipment has been designed and built according to IEC950 and/or the compatible edition of EN60950.
Page 55
CJT 81x 02-10-2001 11:45 Declaration of Conformity Manufacturer’s Name: Manufacturer’s Address: declares that the product: Product Name: CopperJet 812 Conforms to the following standard(s) or other normative document(s): EMC: EN 55022 Class A (1994) Limits and methods of measurement of radio disturbance characteristics of information technology equipment.
Page 56
CJT 81x 02-10-2001 11:45 CopperJet 81x INFORMATION TO USER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 57
CJT 81x 02-10-2001 11:45 Declaration of Conformity Manufacturer’s Name: Manufacturer’s Address: declares that the product: Product Name: CopperJet 813 Conforms to the following standard(s) or other normative document(s): Safety: EN 60950 (1992/93) Safety of information technology equipment, including electrical business equipment. Statement of Conformance to electrical safety &...
Page 58
CJT 81x 02-10-2001 11:45 Pagina 58 CopperJet 81x Warranty This ALLIED DATA TECHNOLOGIES B.V. product is warranted against defects in material and workmanship for a period of five years from date of shipment. During the warranty period, ALLIED DATA TECHNOLOGIES B.V.
Page 59
CJT 81x 02-10-2001 11:45 Pagina 59 Notes:...
Page 60
CJT 81x 02-10-2001 11:45 Allied Data T E C H N O L O G I E S Headoffice Allied Data Technologies bv Netherlands E-mail: support@allieddata.com Website: www.allieddata.com MA-Q-CJT81x-01 Pagina 60 Europe E-mail : support@allieddata.com Website : www.allieddata.com Asia E-mail : support@allieddata.com Website : www.allieddata.com E-mail : USsupport@allieddata.com Website : www.allieddata.com...
Need help?
Do you have a question about the CopperJet 810 and is the answer not in the manual?
Questions and answers