Related Manuals for TURBRO AirSupply BS410
Summary of Contents for TURBRO AirSupply BS410
- Page 1 REGISTER BOOSTER FAN Model: BS410 BS412 IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USE. RETAIN THIS MANUAL FOR FUTURE REFERENCE.
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS ·························································02 SPECIFICATIONS ·····································································03 INSTALLATION ·········································································05 CONTROL PANEL ······································································08 DISPLAY SCREEN ·····································································09 OPERATING ···············································································11 ····························································································16 WARRANTY INFORMATION ······················································17... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS 1. Use the TURBRO register booster fan only as described in this user manual. Do not modify or attempt to repair the device. 2. Keep the device out of reach of children and pets. Use zip ties to prevent the cord from wrapping around the neck and causing suffocation. -
Page 4: Specifications
SPECIFICATIONS Voltage 120V VC to 12V DC Power 17.5W / 12V DC Max Airflow 180CFM Cord Lenght 12ft Remote Control Package Contents Register Fan (x1) Power Adapter (x1) Screw Set (x2) Infrared Remote Control (x1) Zip Tie for Cable Management (x1) - Page 5 Dimensions DIMENSIONS TURBRO BS410 Dimensions 5.51" 3.93" (14.0cm) (10.0cm) 11.54" (29.3cm) 1.96" (5.0cm) 3.93" (10.0cm) 9.72" (24.7cm) TURBRO BS412 Dimensions 5.51" 3.93" (14.0cm) (10.0cm) 13.77" (35.0cm) 1.96" (5.0cm) 3.93" (10.0cm) 9.72" (24.7cm)
-
Page 6: Installation
INSTALLATION Note: Do not install the TURBRO register booster fan on the ceiling or in a location where it may come into contact with water or moisture. Step 1 Measure your register vent to make sure this model will fit. Standard sizes come in 4x10”... - Page 7 STEP 3 Plug the power adapter into an outlet. This can be next to or inside your register. STEP 4 Plug the power adapter cord into the power receptacle of the register fan, and check the display to see if it is illuminated.
- Page 8 STEP 5 Mounted the register fan on the grille. STEP 6 Drill your existing screws into the mounting holes to secure the register fan. If needed, use the attached screws with your register fan. If the screw holes do not align, you may need to drill new holes.
-
Page 9: Control Panel
CONTROL PANEL Duct Temp 1. Mode Button Cycles through the unit’s modes: Duct Temperature display,Cooling Trigger, Heat Trigger, and Fan Speed. 2. Power Button Press and hold the button for 3 seconds to turn on/off. 3. Brightness Button Cycles through the button to choose from three different brightness settings. -
Page 10: Display Screen
DISPLAY SCREEN Duct Temp 2 3 4 5 6 1. Duct Temperature Displays the current temperature of the air flowing through the register. 2. Cooling Trigger Allows you to set a temperature trigger for the fans to run when your air conditioner system is on. - Page 11 Remote Control ‘+’ Button Brightness Button Child Lock Mode Button ‘-’ Button TURBO Function Power Button...
-
Page 12: Operating
OPERATING Important Notes This product is used to boost your existing AC or heater’s airflow. It allows you to set temperature points where the fans will turn on if the airflow’s temperature falls below or rises above the cooling or heating trigger’s setting, respectively. - Page 13 While entering the Cooling Trigger mode the numbers will flash and the default temperature is 82°F, press the ‘+’ or ‘-’ buttons to set the cooling trigger temperature from 32-140°F (0-60°C). Without any input for 8 seconds, the setting will be confirmed and exit the Cooling...
- Page 14 Heating Trigger Adjustment Use this mode to set the temperature trigger for your heater. Please note you are NOT setting your desired temperature. In this mode, the fans will run if the probe temperature meets or rises above the trigger’s hot temperature setting.
- Page 15 3. When the probe detects the 4. The fans will pull heated air from airflow temperature has risen your duct to boost your heater output. above your Heating Trigger setting, it will activate the fans. Duct Temp 5. If the heater is turned off, the probe will detect a lower temperature than your Heating Trigger setting, telling the fans to turn off.
- Page 16 Child Lock Duct Temp To lock the controller, hold the ‘Mode’ button for three or more seconds. The screen will display the Child Lock icon. While the display is locked, the control panel and remote control will not be able to be used until you press and hold the ‘Mode’...
-
Page 17: Faq
Q: What is the TURBRO register booster fan used for? A: The TURBRO register booster fan is used by inserting it into the wall or floor register to boost the airflow and let more cooled or heated air into your room. -
Page 18: Warranty Information
WARRANTY INFORMATION TURBRO provides a 1-year limit for TURBRO Booster Fan, from the date of purchase, subject to the following conditions and limitations. WHAT IS COVERED? ● Any alteration or misuse of the product will nullify this warranty.
Need help?
Do you have a question about the AirSupply BS410 and is the answer not in the manual?
Questions and answers