Kzzi K68Pro Manual

FCC WARNING:
This device complies with part 15 of the FCC Rules, Operation is subiect to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any Changes or modifications not
expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
poursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee that interference wil not occur in
a particular installation.
产品基础
PRODUCT BASIC INFORMATION
说明书 拔轴拔键器
Manual Switch and Keycaps Puller
尺寸/Size
329.4(L)×118.15(W)×37.9(H)±2
K68PRO
89.7(L)×132.5(W)×38.3(H)±2
K20
有线模式
WIERD MODE
K68Pro
连接USB至设备，旋钮拨到OFF为有线模式
Connect the USB to the device and turn the knob to "OFF" for wired mode.
(Note: Wired mode can only be used when the knob in the upper right corner is turned to "OFF".)
BT连接
BT CONNECTION
K68Pro
BT1 BT2
2.4G连接
2.4G RECEIVER CONNECTION
K68Pro
背光控制
BACKLIGHT CONTROL
K68Pro
支持多种背光效果切换
Multiple backlight effects switch
背光亮度+
Backlight brightness +
背光亮度-
Backlight brightness -
窗口锁定
Windows lock
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
键盘 Type-C 数据线 2.4G接收器
Keyboard Type-C Cable 2.4G Receiver
Layout
67 keys
19 keys
(建议: 使用5V 1A额定电源为键盘充电)
(Recommended: Use a 5V 1A power supply for keyboard charging).
拔动开关到BT1、BT2、BT3位置
Toggle switch to BT1、BT2、BT3 for BT Mode.
长按Fn+Q/W/E进入配对模式
Press and hold Fn+Q/W/E to pair with new
BT3
1. 旋钮开关拨到2.4G位置。
2. FN+P长按对码，P键闪烁插入接收器，P键停止闪烁即对码成功。
1.Switch to the 2.4G position,
2.Press and hold FN+P to pair,
As the P key flashing, plug the receiver into the device.
if the P key stops flashing, pairing is successful.
(温馨提示：出厂时已配对好接收器，无需自行再次配对2.4G；此方法只是2.4G无法连接的时候使用，首次设置即可，无需每次都设置)
(Tips: The receiver is set to be paired at the factory You just need to set it only once, when pairing not working properly.)
背光单色切换
Backlight monochrome switching
背光速度 -
Backlight speed -
背光速度+
Backlight speed +
space
长按3秒，恢复出厂设置
bar
WHEN USING A KEYBOARD:
1.Maintain proper posture and avoid excessive force on the keys.
2.Take regular breaks to prevent hand fatigue.
3.Clean the keyboard regularly to remove dust and dirt.
4.Avoid exposing the keyboard to liquids.
5.Keep the keyboard in a suitable environment, free from extreme temperatures or humidity.
Remember these tips for a comfortable and durable keyboard experience.
指示灯
INDICATOR LIGHT
K68Pro Caps Lock Win Lock
K20
Num
充电指示:充电时常亮、充满熄灭低电压时闪烁
Charging indicator: Solid light during charging, off when fully charged, and flashing when battery is low
版本/Version
有线/2.4G/BT
USB-C wired/2.4G wireless/BT
USB Type-c
K20
开关拨到B状态
Setting the switch to the "B" position
BT devices
K20
Long-press for three seconds
to restore factory settings
K68Pro
K20
充电指示:充电时呼吸状态、充满常亮、低电压闪烁
Charging indicator: Breath mode during charging, steady light when fully charged,
and low voltage blinking.
背光/Backlit
RGB
K20
有线模式：连接USB至设备，开关拨到中间为有线模式
Connect the USB cable to the device and set the switch to the middle position for wired mode.
短按Fn+1/2/3至BT频道
Short press Fn+1/2/3 to BT channel
长按Fn+1/2/3进入配对模式
Long press Fn+1/2/3 to enter pairing mode
1. 开关拨到G状态。
2. FN+0长按对码，0键快闪烁插入接收器，0键停止闪烁即对码成功。
1. Switch to the "G" position.To pair the receiver,
2. long-press FN + 0. The 0 key will flash. Insert the receiver and wait for the flashing to stop,
indicating successful pairing.
K20
多种动态背光模式切换
Switch between multiple dynamic backlight modes
背光颜色切换
Switch backlight colors
背光亮度增加
Backlight brightness +
背光亮度减小
Backlight brightness -
长按3秒，恢复出厂设置
Long-press for three seconds
to restore factory settings
MECHANICAL
K E Y B O A R D
轴体/Key Switches
机械轴体
Mechanical switches
3
1 2
BT1 BT2 BT3