Operating Instructions - Kenwood KT-5020 Instruction Manual

Operating instructions
AUTO indicator
Display content
Tuning signal
indicator
Frequency display
(Displays the last channel received}
*Last station
As the memory of this unit is backed up, the frequency
received before the power is turned off is memorized.
This is referred to as the last station frequency. When
the power is turned on again, the unit tunes in the last
station frequency.
■ Auto tuning reception
1. Set the input selector of the amplifier to TUNER.
2. Press the POWER switch.
3. Select the desired band by pressing one of the band
select keys.
• To listen to AM (MW/LW) stations, press the AM
(MW/LW) SELECTOR switch.
The frequency display shows the last AM (MW/LW)
station.
• To listen to FM stations, press the FM SELECTOR
switch.
The frequency display shows the last FM station,
4. Set the TUNING MODE key so that the AUTO indicator
lights.
5. Press the TUNING keys to tune in a station.
• Press the TUNING tS key to tune in a station with a
higher frequency than the current received fre¬
quency, or TUNING [V] key to tune in a frequency
with a lower frequency.
• The stations are automatically scanned.
6. Adjust the volume and tone of your amplifier.
AUTO indicator
Display content_|_
ilr";ss.es-
I ——i
Frequency display
Tuning signal indicator
(Displays the last channel received)
■ Manual tuning
(The reception mode is forced to monaural even when a
FM stereo station is received.)
The manual tuning is to be used for receiving a weak
station which cannot be received by auto tuning.
1. Perform procedures 1 ~ 3 above.
2. Press the TUNING MODE select key so that the AUTO
indicator goes off.
3. Press the TUISTlTsIG key to tune in the desired broad¬
casting station.
• If the TUNING key is held depressed, the frequencies
will change continuously until the key is released.
4. Adjust the volume and tone of your amplifier.
TUNING SIGNAL indicators
As a station is being tuned in, a left or right indicator
lights in red, and the number of lighting points in¬
creases as the signal strength increases. Then, when
the correct tuning is very near, the white points in the
center start to light and increase in number. The station
is tuned most precisely when the number of white
points is at a maximum.
In detuning, the above steps will be reversed.
In AM (MW/LW) reception, the center white indicator
lights when a station is tuned in.
Note: -
If the signal strength of the electric field is insufficient
the left and right indicators will not light more than 4
RED points, or the indication becomes asymmetrical.
■ FM DE-EMPHASIS switch (Except some
areas)
This switch has been set to the correct position for a given
market area. However, check to see that this switch is set
correctly before operating your unit. An incorrect setting
will adversely affect high-frequency performance.
Europe and Oceania ...50 ys
Other countries ...... 75 ys
■ AM/FM CHANNEL SPACE switch (Ex¬
cept some areas)
The CHANNEL SPACE switch on the rear panel is set to
the correct setting that prevails in the area to which the
unit is shipped. However, if the channel space setting is
not matched to the area where the unit is to be used;for
instance, when you moved from area 1 to area 2 or vice
versa, desired reception of AM/FM broadcasts is not
expected. In this case, change the CHANNEL SPACE
setting in accordance with the area corresponding to the
table shown below.
Area Channel Space Frq.
1. U.S.A., Canada
Hawaii, and Guam
FM: 100 kHz
AtC 10 kHz
2. European countries
Far East countries
FM: 50 kHz
AM: 9 kHz
Channel space table
Note: -—-
When changing the setting of the AM/FM CHANNEL SPACE
switch, first unplug the AC power cord, then operate the switch,
and finally insert the AC power cord again.
KT-&020 (En)
9