Advertisement
5. OPERATION
5.1.
BEFORE FIRST USE
5.1.1.
Before using the truck for the first time purge any air from the hydraulic circuit by pumping the foot pedal 10 to 15 times whilst holding
the release lever, fig.3A, in.
5.1.2.
To test the truck, release the lever which will close the hydraulic valve. Pump the foot pedal, fig.1E and raise the truck platform to its
highest position and then pull the valve lever, fig.3.A to lower the platform, (the platform may be slow to descend immediately from its
highest point). If the platform fails to descend adjust the cable length to remove excess play in the release lever movement.
5.2.
USING THE TRUCK
WARNING! Ensure you read, understand and follow the safety instructions. Ensure all Health and Safety, local authority, and
‰
general workshop practice regulations and recommendations are strictly adhered to when lifting or moving heavy loads. The lifting or
movement of heavy loads may be dangerous if not undertaken correctly.
5.2.1.
Move the truck to the required loading area and raise the platform to loading height.
5.2.2.
Lock the truck wheels individually with the wheel foot brakes, see fig.1.
5.2.3.
Load the truck.
5.2.4.
Lower the truck platform to the lowest position before unlocking the wheels.
WARNING! Ensure the load will not foul on anything, and is clear of your hands and the handle when lowering, fig.4.
‰
5.2.5.
Unlock the wheels and transport the load to the required destination.
5.2.6.
To unload, lock the wheels and raise platform if required, then unload the truck.
NOTE: With or without a load, always transport the truck with platform in its lowest position. When not in use, store the truck with the
platform in the lowest position.
6. MAINTENANCE
6.1.
When the truck is not in use, the platform must be in the lowest position to
minimise ram and piston corrosion.
6.2.
Keep the truck clean and wipe off any oil or grease. Lubricate all moving parts
with acid free oil.
DO NOT use truck if believed to have been subjected to abnormal load or
8
shock load. Inspect and if necessary take appropriate action.
6.3.
Periodically check the pump piston and piston rod for signs of corrosion. Clean
exposed areas with a clean oiled cloth.
IMPORTANT: Only fully qualified personnel should attempt maintenance or
repair of the truck hydraulic system.
6.4.
The oil cylinder is a sealed unit and must not be accessed. For service contact
your authorised dealer.
IMPORTANT: All other maintenance and repair (including oil change) must
only be undertaken by fully qualified personnel.
Contact your local authorised service agent.
6.5.
The oil cylinder is a sealed unit and in principle should not be accessed. To top
up or change the oil remove oil plug.
WARNING! Only a good quality hydraulic oil such as SEALEY HYDRAULIC
JACK OIL must be used, DO NOT use brake fluid.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE
OF THE TRUCK.
Hydraulic products are only repaired by local service agents.
We have service/repair agents in all parts of the UK.
DO NOT RETURN TRUCK TO US. Please telephone 01284 757500 to obtain address and 'phone number of your local agent. If truck
is under guarantee please contact your dealer.
De-commissioning the truck: Should the truck become completely unserviceable and require disposal, draw off the oil into an
approved container and dispose of the truck and the oil according to local regulations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
sales@sealey.co.uk
Original Language Version
HPT400H
fig.5
REGISTER YOUR
PURCHASE HERE
www.sealey.co.uk
HPT400H.V2, HPT500.V2
Issue:3 (H,3,F)
Advertisement
