ZALMAN Trimon ZM-M215W User Manual

Zalman trimon zm-m215w: user guide

Hide thumbs

Table Of Contents

Quick Links

ZM-M215W User's Guide

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not

expressly approved by the grantee or manufacturer could void the user's

authority to operate such equipment.

FCC STATEMENT

Table of Contents

Need help?

Do you have a question about the Trimon ZM-M215W and is the answer not in the manual?

Questions and answers

Summary of Contents for ZALMAN Trimon ZM-M215W

Page 1: Fcc Statement
ZM-M215W User’s Guide This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 2: Table Of Contents
• Contents 1. Warning & Cautions 2. Components 3. Cable Connections 4. Function Keys 5. Display Specifications 6. Monitor Specifications 7. Troubleshooting (In 2D/3D Modes)
Page 3: Warning & Cautions
- Install the monitor on a leveled and stable location and place the monitor in a gentle manner. - Do not place candles, cigarettes, or other potential causes of fire on top of the monitor, and do not install the monitor close to a heat source.
Page 4 Disclaimer Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing.
Page 5: Components
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Notice Please use the cables that are provided. Zalman does not take responsibility for any problems that arise from using any other cables.
Page 6: Cable Connections
The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display.
Page 7: Function Keys
4. Function Keys 4-1. Operation of Function Keys Button AUTO MENU ▲ ▼ POWER 4-2. OSD Menu Navigation 1. Press the MENU button, the main OSD menu will be appear on the screen. 2. Press the ▲/▼ buttons to navigate through the menu then press the MENU button to make the selection..
Page 8: Display Specifications
5. Display Specifications Display Modes and Frequencies Resolution Horizontal Frequency (KHz) 1920x1080 1680x1050 1280x1024 1024x768 800x600 640x480 720x400 Vertical Frequency (Hz) 67.5 65.3 48.4 56.5 37.9 48.1 46.9 31.5 37.9 37.4 31.5...
Page 9: Monitor Specifications
6. Monitor Specifications...
Page 10: Troubleshooting
- Check to see if the monitor is running on Power-Saving Mode. - Check to see if the monitor’s power is ON and if the Power Cord is properly connected. 2. If the screen is not clear (if flickering, interference, noise, etc. is present) - Check the VGA cable’s connection state.
Page 11 - This phenomenon is the result of the interference of external light present on the air layer between the LCD screen and the 3D filter. The intensity of this pattern is very weak, which makes it unnoticeable when the LCD screen is ON so the monitor can be used without any inconvenience.
Page 12 4. Reflections are seen on the screen - This monitor has a glass 3D Filter attached to the front side of the LCD. It is not possible to remove the reflections on its surface. Therefore, it is a good idea to not place a light source behind the user.