Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Air-Care TURBOMax III
Summary of Contents for Air-Care TURBOMax III
- Page 1 USER GUIDE...
- Page 2 Division of D.P.L. Enterprises Inc. 3868 East Post Road, Las Vegas, Nevada 89120, (702) 454-5515, FAX (702) 454-5225 Website: www.air-care.com; E-mail: cs@Air-Care.com REV. 02162023 Specifications subject to change without notice.
-
Page 3: Table Of Contents
PAGE 3 TABLE OF CONTENTS CHAPTER PAGE Unpacking Instructions Safety Precautions Handle Installation Operating Instructions Attaching the TurboMax Hose to the Air System Duct Cleaning Procedures Troubleshooting Guide Maintenance Parts and Accessories Included Parts and Accessories Optional Parts Specifications Limited Warranty... - Page 4 “Operating” section of this manual. Inspect all of the packing material for small parts before discarding packaging material. Report all damage to Air-Care immediately. Any attempt at repairing damages may void warranty. Check that all parts are present TurboMax 3 Main Assembly, with Wheels, Motor and Blower. Release the 4 side latches and lift the front of the upper section so it hinges up to check for filters.
-
Page 5: Handle Installation
• Never allow anyone but a properly trained technician to use the equipment or cleaning products. • The TurboMax 3 has a 220-120 step down transformer to run on 220 volt power. All Air-Care equipment is designed for US standard 115 volt, 60 Hz AC. Most Air-Care equipment can be special ordered to meet other worldwide standards for a reasonable price and delivery schedule. -
Page 6: Operating Instructions
OPERATING INSTRUCTIONS Set-Up and Testing Air-Care TurboMax Negative air machines are designed to “Pull” loose debris out of the air system to which they are connected and filter out harmful debris such as pollen, dust, mold spores and other debris with their 3 stage HEPA filter system. An agitating device to “Push” debris is required to properly clean an air system. -
Page 7: Attaching The Turbomax Hose To The Air System
PAGE 7 ATTACHING TURBOMAX 3 HOSE TO THE AIR SYSTEM Effective duct cleaning can be accomplished with the TurboMax connected to one of the following positions in the duct system. The “best” location is determined by the specific configuration of the particular air system. -
Page 8: Duct Cleaning Procedures
PAGE 8 DUCT CLEANING PROCEDURES 2. Connect the 12 gauge, 3. Connect a 12” hose to the 1. Bring the TurboMax into grounded, electrical power 12” TurboMax inlet. To obtain close proximity to the planned cords to an independent maximum “pull”, always keep connection ducts. - Page 9 PAGE 9 DUCT CLEANING PROCEDURES 7. Use the RUN switch to start 8. Follow recommended 9. After all ducts are cleaned, the TurboMax 3 motor. procedure to clean each supply, the ducts can be fogged with an beginning at the most distant EPA registered Deodorizer and one, using the Cobra Power Soot Set Sealer.
-
Page 10: Troubleshooting Guide
Contact Air-Care No vacuum with motor Is blower turning? running. Tighten shaft adapter bolts and align wheel & inlet cone. (Call Air-Care) Replace HEPA filters as required. Are the 1st stage pre- Is the “Change HEPA” filter and 2nd stage... -
Page 11: Maintenance
2nd stage filter with a garden hose and nozzle at full force. First rinse in the opposite direction of the airflow, then rinse both sides. Occasionally, a degreaser such as Air-Care’s Filter Cleaner may be required to restore this filter to its’... -
Page 12: Parts And Accessories
Foam Register Plugs, 14pc./pkg. (Optional) FG0050 Pre-Filter, Pellon Moisture Barrier Sheets, 12/pkg. (Optional) SAO0079 12” Adapter Collar FG0041 Air-Care Fogger Model 2600 120 Volt(for 220 Volt Call) (Optional) FG0008 Cobra 6, Power Brush System (Optional) FG0110 Forward and Reverse Air Whisk System (Optional) FG0015... -
Page 13: Included Parts And Accessories
PAGE 13 INCLUDED PARTS AND ACCESSORIES Molded Handle 12” Dia. Hose Inlet Locking Latches First stage, 18” x 24” x 1” Electrostatic Filter with Pads 2nd Stage 18” x 24”Flex 94% Electrostatic Air Filter 3rd Stage 18” x 24” x 4.75” HEPA Filter 12”... -
Page 14: Optional Parts
PAGE 14 OPTIONAL PARTS AND ACCESSORIES (Ref#19) 12” x 12”, 26 gauge, Galvanized Steel Duct Patches 12” x 12” , 26 gauge, 12” Adapter Plate (Ref#21) Pre-Filter, Pellon Galvanized Steel Duct Moisture Barrier Sheets (12/pkg) Patches Pre-Filter, Pellon Moisture Barrier Sheets (12/pkg) Cobra Power Brush System Foam Register Plugs... -
Page 15: Specifications
PAGE 15 SPECIFICATIONS Specification Description Size 19.5” W x 29” D x 55 ½” H Weight 146 lbs. Power required 120 V, 60 Hz, 20 amps. Power Cord 25’ , 3 x 12 Ga. Extension Cords Filtration 4 stages when Pellon pre-filter used Pre-Filter Pellon Moisture Barrier 1st Stage 18”... -
Page 16: Limited Warranty
1 Year Wheels & Filters No Warranty Warranty covers both parts and labor (labor is to be performed at Air-Care’s facility located at 3868 E. Post Road; Las Vegas, Nevada). Warranty is extended to the original purchaser and is not transferrable. - Page 17 PAGE 17...
Need help?
Do you have a question about the TURBOMax III and is the answer not in the manual?
Questions and answers