A Specifications - Kenwood KR-A5050 Instruction Manual

Specifications (For the U.S.A. and Canada)
[AUDIO section]
Rated power output (FTC)
STEREO MODE
100 watts per channel minimum RMS, both channels
driven, at 8 a from 20 Hz to 20,000 Hz with no more
than 0.06 % total harmonic distortion.
Total harmonic distortion
.0.03 % (1 kHz, 50 W, 8 £2)
Signal to noise ratio
(IHF'66)
PHONO (MM)...73 dB
LINE (CD,TAPE, VIDEO) ....100 dB
Input sensitivity / impedance
PHONO (MM).2.5 mV / 47 Id}
LINE (CD, TAPE, VIDEO).200 mV /47 k£2
Tone control
BASS.± 10 dB (at 100 Hz)
TREBLE.± 10 dB (at 10 kHz)
Loudness control (volume at -30 dB level)
.-.+ 9dB (100 Hz)
[AM tuner section]
Tuning frequency range. 530 kHz ~ 1,700 kHz
Usable sensitivity.16
p
V / (400
jx
V/m)
Signal to noise ratio (at 30% mod. ImV input) ....50 dB
Total harmonic distortion.........0.5 %
Selectivity........23 dB
[General]
Power consumption.2,5 A
AC outlet
SWITCHED...2: (Total 150W max.)
Dimensions.W: 440 mm (17-5/16")
H : 129 mm (5-1/16")
D : 379 mm (14-15/16")
Weight (Net).10.2 kg (22,5 lb)
[FM tuner section]
Tuning frequency range.87.5 MHz - 108 MHz
Usable sensitivity (MONO at 75 £2) ..0.95 jx V / 10.8 dBf
50 dB quieting sensitivity (at 750)
MONO...2.0 jx V / 17.2 dBf
STEREO.25.0 p V / 39.2 dBf
Total harmonic distortion (at 1 kHz)
MONO.0.4 % (65 dBf input)
STEREO.0.5 % (65 dBf input)
Signal to noise ratio (at 1 kHz)
MONO.78 dB (65 dBf input)
STEREO.73 dB (65 dBf input)
Stereo separation
1 kHz.. dB
Selectivity (± 400 kHz)...50 dB
Frequency response (30 Hz - 15 kHz)
.. 0.5 dB, -2.0 dB
For the U.S.A.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
hmits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause
harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular installation, [f this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- - increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radio/TV technician for help.
Note:
KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
KR-A5050 (En!
19